Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM30B0U _59 Vehicle Exterior _009875 DOOR / HATCH _0054766 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

w/ Side Airbag:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

a.
B337327

Detach the 2 claws and 2 clips and remove the front door lower frame bracket garnish LH.


Hide 4.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

a.
B337328

Using a moulding remover, detach the 2 clips, 6 claws and 2 guides and remove the power window regulator master switch assembly with front door armrest base panel.


b.

Disconnect the connector.


Hide 5.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Driver Side)

Hide 6.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

a.
B337002

Using a moulding remover, detach the 2 clips, 6 claws and 2 guides and remove the power window regulator master switch assembly with front door armrest base panel.


b.

Disconnect the connector.


Hide 7.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

Hide 8.REMOVE DOOR CONTROL SWITCH (for Front Passenger Side)

Hide 9.REMOVE FRONT DOOR ASSIST GRIP COVER LH

a.
B337329

Using a moulding remover, detach the 4 claws, 2 clips and guide and remove the front door assist grip cover LH.


Hide 10.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

a.
B337330

Detach the 3 claws and remove the front door inside handle bezel plug LH.


Hide 11.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B337333

Remove the 3 screws.


b.
B337331

Detach the 9 clips and remove the front door trim board sub-assembly.


c.
B337332

Disengage the front door lock remote control cable assembly LH and front door inside locking cable assembly LH from the 2 clamps.


d.

Disconnect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH.


e.

for Power Seat:

Disconnect the connector.


Hide 12.REMOVE SEAT MEMORY SWITCH

Hide 13.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.
B337334

Detach the 2 claws and guide and remove the front door inside handle sub-assembly LH.


Hide 14.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

a.
B337335

Raise the 7 claws of the front door inner glass weatherstrip LH as shown in the illustration, and then remove the front door inner glass weatherstrip LH from the front door trim board sub-assembly LH.


Hide 15.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 17.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

Hide 18.REMOVE FRONT DOOR SERVICE HOLE COVER LH

a.
B338198

Disconnect the connector.


b.

Remove the bolt as shown in the illustration.


c.

Using a clip remover, detach the 3 clamps.


d.

Pull out the front door lock remote control cable assembly LH, front door inside locking cable assembly LH and wire harness from the front door service hole cover LH, and then remove the front door service hole cover LH.

HINT:

Remove any remaining butyl tape from the front door panel.



Hide 19.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

a.

Temporarily install the power window regulator master switch assembly with front door armrest base panel.


b.

Connect the power window regulator motor.


c.

Connect the cable to the negative (-) battery terminal.


d.

Move the front door window regulator so that the front door glass bolts can be seen.


e.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



f.

Remove the power window regulator master switch assembly with front door armrest base panel.


g.
B337338

Remove the 2 bolts.

NOTICE:

After the bolts are removed, do not allow the front door glass to fall.



h.
B337339
0.604,0.552 0.958,0.75 0.354,0.198 10 (1) 1.854,0.26 2.135,0.458 0.281,0.198 10 (2)

Remove the front door glass sub-assembly LH as indicated by the arrows in the order shown in the illustration.

NOTICE:

Do not damage the front door glass.



Hide 20.REMOVE FRONT DOOR GLASS RUN LH

a.
B337341

Remove the front door glass run LH.


Hide 21.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.
B337340
2.094,1.146 1.844,0.354 1.844,0.354 1.625,0.354 true 1.479,0.271 1.698,0.448 0.219,0.177 10 *1
*1 Temporary Bolt


Disconnect the connector.


b.

Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator sub-assembly LH may fall and become damaged.



c.

Remove the 5 bolts and front door window regulator sub-assembly LH.


d.

Remove the temporary bolt from the front door window regulator sub-assembly LH.


Hide 22.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 23.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.
B337342

Remove the bolt.


b.
B337343

Detach the guide and remove the front door rear lower frame sub-assembly LH.


Hide 24.REMOVE FRONT DOOR NO. 2 STIFFENER CUSHION

a.
B338197
1.552,1.052 1.594,1.125 false
V100155

Double-sided Tape


Remove the 2 bolts.


b.

Detach the 2 guides, and remove the double-sided tape and front door No. 2 stiffener cushion.

NOTICE:

Remove any remaining tape from the door.



Hide 25.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY LH

Hide 26.REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH

a.
B338129
3,1.615 3,1.271 false 2.927,1.646 3.24,1.802 0.313,0.156 10 *1
*1 Hole Plug


Remove the hole plug.


b.

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover LH together with the door lock cylinder LH.


Hide 27.REMOVE DOOR LOCK CYLINDER LH

a.
B337345

Detach the 2 claws and remove the door lock cylinder LH from the front door outside handle cover LH.


Hide 28.REMOVE FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH

Hide 29.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.
B342164

Remove the front door lock remote control cable assembly LH.


Hide 30.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B342165

Detach the 3 claws and open the cover.


b.
B342166

Remove the front door inside locking cable assembly LH.


Hide 31.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.

w/ Entry and Start System:

i.
B337346
2.333,0.844 2.656,0.542 2.656,0.542 2.844,0.542 false 2.854,0.448 3.052,0.635 0.198,0.188 10 *1
*1 Protective Tape


Using a screwdriver, detach the 2 claws of the connector cover in the direction indicated by the arrow in the illustration and disconnect the connector cover.

HINT:

Tape the screwdriver tip before use.



ii.
B338126
1.958,1 2.26,0.594 2.26,0.594 2.573,0.594 false 2.594,0.5 2.74,0.677 0.146,0.177 10 *1
*1 Protective Tape


Using a screwdriver, detach the claw of the connector in the direction indicated by the arrow in the illustration and disconnect the connector.

HINT:

Tape the screwdriver tip before use.




b.
B337347

Remove the front door outside handle assembly LH by sliding and pulling it in the direction indicated by the arrow in the illustration.


Hide 32.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B337350

Detach the 3 claws and remove the front door front outside handle pad.


Hide 33.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B337351

Detach the 2 claws and remove the front door rear outside handle pad.


Hide 34.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.
B338196

w/ Entry and Start System:

Detach the 3 clamps.


b.
B338199
0.052,0.031 0.365,0.188 0.313,0.156 10 *A 0.052,2.26 0.365,2.417 0.313,0.156 10 *B
*A Inside
*B Outside


Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle frame sub-assembly LH.


c.

Slide the front door outside handle frame sub-assembly LH to detach the claw of the front door outside handle frame sub-assembly LH, and then remove it.


Hide 35.REMOVE FRONT DOOR LOCK OPEN ROD LH

a.
B332412
2.604,0.656 3.052,0.333 true 2.552,0.104 3.01,0.302 0.458,0.198 10 (1) 2.729,0.854 3.188,1.052 0.458,0.198 10 (2) 3.021,0.208 3.208,0.396 0.188,0.188 10 *1
*1 Snap


Rotate the snap to detach the snap, and then remove the front door lock open rod LH as indicated by the arrows in the order shown in the illustration.


Hide 36.REMOVE FRONT DOOR CHECK ASSEMBLY LH

a.
B337360

Remove the 3 bolts and front door check assembly LH.


Hide 37.REMOVE FRONT DOOR WEATHERSTRIP LH

a.
B337356

Using a clip remover, remove the 2 clips.


b.

Using a clip remover, detach the 18 clips and remove the front door weatherstrip LH.


Hide 38.REMOVE DOOR FRAME GARNISH LH

a.
B337359

Detach the claw and remove the door frame garnish LH.


Hide 39.REMOVE DOOR WINDOW FRAME MOULDING CLIP

Hide 40.REMOVE FRONT DOOR WINDOW REAR FRAME MOULDING LH

Hide 42.REMOVE FRONT DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH

Hide 43.REMOVE FRONT DOOR PANEL CUSHION

a.
B337357

Detach the 2 claws and remove the 2 front door panel cushions.