Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM
RM30B0U _59 Vehicle Exterior _009987 SLIDING ROOF / CONVERTIBLE _0054777 SLIDING ROOF SYSTEM C

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  B2341  Sensor (Motor) Failure  B2344  Position Failure  


DESCRIPTION

When the sliding roof drive gear sub-assembly (sliding roof ECU) detects a motor malfunction and the sliding roof operation is stopped, DTC B2341 is stored.

When the sliding roof drive gear sub-assembly (sliding roof ECU) detects a gear position malfunction and the sliding roof operation is stopped, DTC B2344 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2341 Sensor (Motor) Failure Sensor (motor) failure (When the sliding roof ECU enters fail-safe mode due to a problem with the motor)
·

Sliding roof drive gear sub-assembly (Sliding roof ECU)

·

Map light assembly (Sliding roof control switch)

·

Harness or connector


B2344 Position Failure Position failure (When the sliding roof ECU enters fail-safe mode due to a problem with the gear position)
·

Sliding roof drive gear sub-assembly (Sliding roof ECU)

·

Map light assembly (Sliding roof control switch)

·

Harness or connector



WIRING DIAGRAM

B271000
4.615,4.896 4.938,5.073 0.323,0.177 10 Q8 2.458,4.219 2.74,4.396 0.281,0.177 10 Q7 5.052,2.802 5.427,3.021 0.375,0.219 10 OPN 5.052,3.042 5.396,3.24 0.344,0.198 10 CLS 5.052,3.802 5.333,3.979 0.281,0.177 10 UP 5.052,3.552 5.583,3.729 0.531,0.177 10 DWN 4.896,2.698 5.031,2.875 0.135,0.177 10 7 4.896,2.958 5.031,3.135 0.135,0.177 10 5 4.896,3.458 5.031,3.635 0.135,0.177 10 6 4.896,3.708 5,3.885 0.104,0.177 10 4 3.75,2.698 4.094,2.875 0.344,0.177 10 OPN 3.792,2.958 4.115,3.198 0.323,0.24 10 CLS 3.615,3.458 4.104,3.667 0.49,0.208 10 DOWN 3.875,3.708 4.115,3.906 0.24,0.198 10 UP 4.156,2.698 4.26,2.875 0.104,0.177 10 3 4.156,2.958 4.26,3.135 0.104,0.177 10 2 4.156,3.708 4.25,3.885 0.094,0.177 10 5 4.156,3.458 4.271,3.635 0.115,0.177 10 4 2.427,2.833 2.833,3.031 0.406,0.198 10 GND3 2.25,2.833 2.438,3.01 0.188,0.177 10 1 5.813,4.094 5.938,4.271 0.125,0.177 10 E 5.979,4 6.188,4.177 0.208,0.177 10 12 2.563,0.99 4.729,1.385 2.167,0.396 10 Main Body ECU (Multiplex Network Body ECU) 0.875,0.979 2.104,1.333 1.229,0.354 10 Combination Meter Assembly 3.667,0.521 4,0.688 0.333,0.167 10 LIN2 2.99,0.521 3.354,0.688 0.365,0.167 10 CAN 1.656,0.521 2.021,0.688 0.365,0.167 10 CAN 5.063,0.521 5.479,0.688 0.417,0.167 10 MPX1 0.688,5.448 2.333,5.635 1.646,0.188 10 : LIN Communication Line 0.688,5.115 2.427,5.302 1.74,0.188 10 : CAN Communication Line 2.458,4.396 4.24,4.771 1.781,0.375 10 Map Light Assembly (Sliding Roof Control Switch) 4.615,5.073 6.979,5.479 2.365,0.406 10 Sliding Roof Drive Gear Sub-assembly (Sliding Roof ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

When the sliding roof drive gear sub-assembly (sliding roof ECU) is removed and reinstalled or replaced, it requires initialization.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

·

The sliding roof system uses the CAN and LIN communication systems. First, confirm that there are no malfunctions in the CAN and LIN communication systems. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK SLIDING ROOF OPERATION
a.

Result:
Proceed to
Auto operation operates normally
Auto operation does not operate normally



Auto operation operates normally

2.CHECK DTC OUTPUT

Auto operation does not operate normally

3.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)
2.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR

Body Electrical > Sliding Roof > Clear DTCs
50002 147

b.

Check for DTCs.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR

Body Electrical > Sliding Roof > Trouble Codes
50001 147

Result:
Proceed to
DTC B2341 or B2344 is not output
DTC B2341 or B2344 is output



DTC B2341 or B2344 is not output

DTC B2341 or B2344 is output

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

3.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)
a.

Check that the sliding roof drive gear sub-assembly (sliding roof ECU) can be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

OK:

Sliding roof drive gear sub-assembly (sliding roof ECU) can be initialized.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC OUTPUT

NG

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF CONTROL SWITCH AND BODY GROUND)
4.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR

Body Electrical > Sliding Roof > Clear DTCs
50002 147

b.

Check for DTCs.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR

Body Electrical > Sliding Roof > Trouble Codes
50001 147

Result:
Proceed to
DTC B2341 or B2344 is not output
DTC B2341 or B2344 is output



DTC B2341 or B2344 is not output

END (PROBLEM DUE TO INITIALIZATION FAILURE)

DTC B2341 or B2344 is output

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF CONTROL SWITCH AND BODY GROUND)
a.

Disconnect the Q7 map light assembly (sliding roof control switch) connector.


b.

Disconnect the Q8 sliding roof drive gear sub-assembly (sliding roof ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q8-5 (CLS) - Q7-2 (CLS) Always Below 1 Ω
Q8-5 (CLS) - Body ground Always 10 kΩ or higher
Q8-7 (OPN) - Q7-3 (OPN) Always Below 1 Ω
Q8-7 (OPN) - Body ground Always 10 kΩ or higher
Q8-6 (DWN) - Q7-4 (DOWN) Always Below 1 Ω
Q8-6 (DWN) - Body ground Always 10 kΩ or higher
Q8-4 (UP) - Q7-5 (UP) Always Below 1 Ω
Q8-4 (UP) - Body ground Always 10 kΩ or higher
Q7-1 (GND3) - Body ground Always Below 1 Ω
Q8-12 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF CONTROL SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF CONTROL SWITCH)
a.
B338690
1.417,1.146 0.844,0.833 0.844,0.833 0.49,0.833 true 1.615,1.135 1.042,0.521 1.042,0.521 0.781,0.521 true 1.823,1.135 2.083,0.5 2.083,0.5 2.354,0.5 true 2.01,1.135 2.396,0.719 2.396,0.719 2.667,0.719 true 2.271,1.219 2.448,1.344 2.448,1.344 2.719,1.344 true 0.271,0.76 0.5,0.958 0.229,0.198 10 UP 0.302,0.448 0.781,0.615 0.479,0.167 10 DOWN 2.406,0.417 2.885,0.583 0.479,0.167 10 OPN 2.719,0.646 3.198,0.813 0.479,0.167 10 CLS 2.76,1.26 3.24,1.427 0.479,0.167 10 GND3

Remove the map light assembly (sliding roof control switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (UP) - 1 (GND3) UP switch is pressed Below 1 Ω
5 (UP) - 1 (GND3) UP switch is not pressed 10 kΩ or higher
4 (DOWN) - 1 (GND3) DOWN switch is pressed Below 1 Ω
4 (DOWN) - 1 (GND3) DOWN switch is not pressed 10 kΩ or higher
3 (OPN) - 1 (GND3) OPEN switch is pressed Below 1 Ω
3 (OPN) - 1 (GND3) OPEN switch is not pressed 10 kΩ or higher
2 (CLS) - 1 (GND3) CLOSE switch is pressed Below 1 Ω
2 (CLS) - 1 (GND3) CLOSE switch is not pressed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

REPLACE MAP LIGHT ASSEMBLY (SLIDING ROOF CONTROL SWITCH)