Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM
RM30B0U _59 Vehicle Exterior _009987 SLIDING ROOF / CONVERTIBLE _0054777 SLIDING ROOF SYSTEM Y

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the sliding roof system.

·

*: Use the Techstream.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points in problem analysis:

What Vehicle, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms



Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

4.INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
4.INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Using the Techstream, check if the CAN Communication System is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Proceed to
DTCs are not output
DTCs are output



DTCs are not output

5.INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

DTCs are output

5.INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
a.

Using the Techstream, check if the LIN Communication System is functioning normally.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR


Result:
Proceed to
DTCs are not output
DTCs are output



DTCs are not output

6.PROBLEM SYMPTOMS TABLE

DTCs are output

6.PROBLEM SYMPTOMS TABLE

Result:
Proceed to
Fault is not listed in problem symptoms table
Fault is listed in problem symptoms table



Fault is not listed in problem symptoms table

7.OVERALL ANALYSIS AND TROUBLESHOOTING*

Fault is listed in problem symptoms table

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

7.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

8.ADJUST, REPAIR OR REPLACE
8.ADJUST, REPAIR OR REPLACE
a.

Check if the sliding roof drive gear sub-assembly has been replaced, or the sliding roof glass sub-assembly or sliding roof drive cable sub-assembly has been adjusted, or removed and installed.


Result:
Result Proceed to
The sliding roof drive gear sub-assembly has been replaced, or sliding roof glass sub-assembly or sliding roof drive cable sub-assembly has been adjusted, or removed and installed. A
None of the sliding roof drive gear sub-assembly has been replaced, and sliding roof glass sub-assembly and sliding roof drive cable sub-assembly have been adjusted, and removed and installed. B



A

9.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

B

10.CONFIRMATION TEST
9.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)
a.

Initialize the sliding roof drive gear sub-assembly (sliding roof ECU).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

HINT:

If initialization has not been performed, the auto operation, jam protection function, key-off operation and sliding roof open warning will not operate or will operate incorrectly.



Result:
Proceed to
NEXT



NEXT

10.CONFIRMATION TEST
10.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END