Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM
RM30B0U _59 Vehicle Exterior _009987 SLIDING ROOF / CONVERTIBLE _0054777 SLIDING ROOF SYSTEM C

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  B2342  Switch Failure  


DESCRIPTION

This DTC is stored when the sliding roof drive gear sub-assembly (sliding roof ECU) detects that the sliding roof control switch is stuck for 30 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2342 Switch Failure Sliding roof drive gear sub-assembly (sliding roof ECU) detects sliding roof control switch is stuck for 30 seconds or more.
·

Sliding roof drive gear sub-assembly (Sliding roof ECU)

·

Map light assembly (Sliding roof control switch)

·

Harness or connector



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When the sliding roof drive gear sub-assembly (sliding roof ECU) is removed and reinstalled or replaced, it requires initialization.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION


PROCEDURE

1.READ VALUE USING TECHSTREAM
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Sliding Roof / Data List.


e.

Read the Data List according to the display on the Techstream.

Body Electrical > Sliding Roof > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Open Switch Failure(Past) Open switch failure signal (Past) ON or OFF ON: Sliding roof open switch failure signal (Past)
OFF: No sliding roof open switch failure signal (Past)
-
Close Switch Failure(Past) Close switch failure signal (Past) ON or OFF ON: Sliding roof close switch failure signal (Past)
OFF: No sliding roof close switch failure signal (Past)
-
Up Switch Failure(Past) Up switch failure signal (Past) ON or OFF ON: Sliding roof up switch failure signal (Past)
OFF: No sliding roof up switch failure signal (Past)
-
Down Switch Failure(Past) Down switch failure signal (Past) ON or OFF ON: Sliding roof down switch failure signal (Past)
OFF: No sliding roof down switch failure signal (Past)
-
Open Switch Failure(Current) Open switch failure signal (Current) ON or OFF ON: Sliding roof open switch failure signal (Current)
OFF: No sliding roof open switch failure signal (Current)
-
Close Switch Failure(Current) Close switch failure signal (Current) ON or OFF ON: Sliding roof close switch failure signal (Current)
OFF: No sliding roof close switch failure signal (Current)
-
Up Switch Failure(Current) Up switch failure signal (Current) ON or OFF ON: Sliding roof up switch failure signal (Current)
OFF: No sliding roof up switch failure signal (Current)
-
Down Switch Failure(Current) Down switch failure signal (Current) ON or OFF ON: Sliding roof down switch failure signal (Current)
OFF: No sliding roof down switch failure signal (Current)
-
Body Electrical > Sliding Roof > Data List
Tester Display
Open Switch Failure(Past)
Close Switch Failure(Past)
Up Switch Failure(Past)
Down Switch Failure(Past)
Open Switch Failure(Current)
Close Switch Failure(Current)
Up Switch Failure(Current)
Down Switch Failure(Current)
50003 147 32,33,34,35,36,37,38,39

Result:
Proceed to
"OFF" appears on the Techstream screen
"ON" appears on the Techstream screen



"OFF" appears on the Techstream screen

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

"ON" appears on the Techstream screen

2.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BODY GROUND)
a.

Disconnect the Q8 sliding roof drive gear sub-assembly (sliding roof ECU) connector.


b.

Disconnect the Q7 map light assembly (sliding roof control switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q8-7 (OPN) - Body ground Always 10 kΩ or higher
Q8-6 (DWN) - Body ground Always 10 kΩ or higher
Q8-5 (CLS) - Body ground Always 10 kΩ or higher
Q8-4 (UP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF CONTROL SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF CONTROL SWITCH)
a.
B338690
1.417,1.146 0.844,0.833 0.844,0.833 0.49,0.833 true 1.615,1.135 1.042,0.521 1.042,0.521 0.781,0.521 true 1.823,1.135 2.083,0.5 2.083,0.5 2.354,0.5 true 2.01,1.135 2.396,0.719 2.396,0.719 2.667,0.719 true 2.271,1.219 2.448,1.344 2.448,1.344 2.719,1.344 true 0.271,0.76 0.5,0.958 0.229,0.198 10 UP 0.302,0.448 0.781,0.615 0.479,0.167 10 DOWN 2.406,0.417 2.885,0.583 0.479,0.167 10 OPN 2.719,0.646 3.198,0.813 0.479,0.167 10 CLS 2.76,1.26 3.24,1.427 0.479,0.167 10 GND3

Remove the map light assembly (sliding roof control switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (UP) - 1 (GND3) UP switch is pressed Below 1 Ω
5 (UP) - 1 (GND3) UP switch is not pressed 10 kΩ or higher
4 (DOWN) - 1 (GND3) DOWN switch is pressed Below 1 Ω
4 (DOWN) - 1 (GND3) DOWN switch is not pressed 10 kΩ or higher
3 (OPN) - 1 (GND3) OPEN switch is pressed Below 1 Ω
3 (OPN) - 1 (GND3) OPEN switch is not pressed 10 kΩ or higher
2 (CLS) - 1 (GND3) CLOSE switch is pressed Below 1 Ω
2 (CLS) - 1 (GND3) CLOSE switch is not pressed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

REPLACE MAP LIGHT ASSEMBLY (SLIDING ROOF CONTROL SWITCH)