Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM30B0U _58 Vehicle Interior _009988 HEATING / AIR CONDITIONING _0054778 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1411/11  Room Temperature Sensor Circuit  


DESCRIPTION

The cooler (room temperature sensor) thermistor is installed in the instrument panel to detect the cabin temperature which is used to control the heater and air conditioning system AUTO mode. The resistance of the cooler (room temperature sensor) thermistor changes in accordance with the cabin temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies a voltage (5 V) to the cooler (room temperature sensor) thermistor and reads voltage changes due to changes in the resistance of the cooler (room temperature sensor) thermistor.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1411/11 Room Temperature Sensor Circuit Open or short in cooler (room temperature sensor) thermistor circuit
·

Cooler (room temperature sensor) thermistor

·

Harness or connector

·

Air conditioning amplifier assembly


Memorized (4 seconds or more) -

HINT:
·

The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the brackets.

·

If the cabin temperature is approximately -18.6°C (-1.48°F) or less, DTC B1411/11 may be output even though the system is normal.



WIRING DIAGRAM

E236721
2.146,0.448 2.531,0.844 0.385,0.396 10 1 2.146,1.396 2.646,1.729 0.5,0.333 10 2 5.115,0.448 5.552,0.75 0.438,0.302 10 29 5.115,1.406 5.51,1.708 0.396,0.302 10 34 5.396,0.542 6.146,0.958 0.75,0.417 10 TR 5.396,1.49 6.146,1.833 0.75,0.344 10 SG-1 0.938,1.917 1.26,2.094 0.323,0.177 10 G19 0.938,2.115 2.615,2.604 1.677,0.49 10 Cooler (Room Temperature Sensor) Thermistor 5.083,1.906 5.365,2.083 0.281,0.177 10 G81 5.083,2.073 6.667,2.542 1.583,0.469 10 Air Conditioning Amplifier Assembly

CAUTION / NOTICE / HINT

NOTICE:

When the battery is disconnected or the air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>INITIALIZATION


PROCEDURE

1.READ VALUE USING TECHSTREAM
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Room Temperature Sensor Cooler thermistor (room temperature sensor) Min.: -6.50°C (20.30°F)
Max.: 57.25°C (135.05°F)
Actual cabin temperature displayed -
Body Electrical > Air Conditioner > Data List
Tester Display
Room Temperature Sensor
50003 121 1
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
OK (When troubleshooting according to Problem Symptoms Table) A
OK (When troubleshooting according to the DTC) B
NG C



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

2.INSPECT COOLER (ROOM TEMPERATURE SENSOR) THERMISTOR
2.INSPECT COOLER (ROOM TEMPERATURE SENSOR) THERMISTOR
a.

Remove the cooler (room temperature sensor) thermistor.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>ROOM TEMPERATURE SENSOR>REMOVAL


b.

Inspect the cooler (room temperature sensor) thermistor.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>ROOM TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COOLER [ROOM TEMPERATURE SENSOR] THERMISTOR)

NG

REPLACE COOLER (ROOM TEMPERATURE SENSOR) THERMISTOR

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COOLER [ROOM TEMPERATURE SENSOR] THERMISTOR)
a.

Disconnect the G81 air conditioning amplifier assembly connector.


b.

Disconnect the G19 cooler (room temperature sensor) thermistor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G81-29 (TR) - G19-1 Always Below 1 Ω
G81-34 (SG-1) - G19-2 Always Below 1 Ω
G81-29 (TR) - Body ground Always 10 kΩ or higher
G81-34 (SG-1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR