Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)
RM30B0U _58 Vehicle Interior _009988 HEATING / AIR CONDITIONING _0054779 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1412  Ambient Temperature Sensor Circuit  


DESCRIPTION

The cooler (ambient temperature sensor) thermistor is installed in front of the cooler condenser assembly to detect the ambient temperature which is used to control the air conditioning system. This sensor is connected to the combination meter assembly and detects fluctuations in the ambient temperature. This data is used for controlling the cabin temperature. The sensor sends a signal to the combination meter assembly. The resistance of the thermistor assembly changes in accordance with the ambient temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The combination meter assembly applies voltage (5 V) to the cooler (ambient temperature sensor) thermistor and reads voltage changes due to changes in the resistance of the cooler (ambient temperature sensor) thermistor.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1412 Ambient Temperature Sensor Circuit Open or short in cooler (ambient temperature sensor) thermistor circuit
·

Cooler (ambient temperature sensor) thermistor

·

Harness or connector

·

Air conditioning amplifier assembly

·

Combination meter assembly

·

CAN communication system


Memorized
(4 seconds or more)*

*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


HINT:

If the ambient temperature is approximately -52.9°C (-63.22°F) or less, DTC B1412 may be output even though the system is normal.


WIRING DIAGRAM

E269965
0.188,2.24 0.646,2.438 0.458,0.198 10 A26 0.177,2.427 2.094,2.792 1.917,0.365 10 Cooler (Ambient Temperature Sensor) Thermistor 2.729,2.25 3.188,2.448 0.458,0.198 10 G16 2.729,2.427 4.646,2.792 1.917,0.365 10 Combination Meter Assembly 5.604,1.833 6.063,2.031 0.458,0.198 10 CANL 5.344,2.427 6.969,2.802 1.625,0.375 10 Air Conditioning Amplifier Assembly 5.594,0.875 6.052,1.073 0.458,0.198 10 CANH 5.385,0.698 5.563,0.906 0.177,0.208 10 8 4.146,0.708 4.604,0.906 0.458,0.198 10 32 4.156,1.667 4.615,1.865 0.458,0.198 10 31 5.385,1.677 5.594,1.875 0.208,0.198 10 9 3.677,1.813 4.135,2.01 0.458,0.198 10 CANL 3.667,0.875 4.125,1.073 0.458,0.198 10 CANH 3.115,0.875 3.573,1.073 0.458,0.198 10 TX1+ 3.115,1.823 3.573,2.021 0.458,0.198 10 TX1- 1.073,1.927 1.531,2.125 0.458,0.198 10 SO- 1.083,0.969 1.542,1.167 0.458,0.198 10 SO+ 1.458,0.74 1.917,0.938 0.458,0.198 10 2 1.448,1.677 1.906,1.875 0.458,0.198 10 1 2.833,0.74 3.292,0.938 0.458,0.198 10 35 2.833,1.698 3.292,1.896 0.458,0.198 10 34 5.354,2.26 5.813,2.458 0.458,0.198 10 G80 0.74,3.396 2.677,3.594 1.938,0.198 10 : CAN Communication Line

PROCEDURE

1.READ VALUE USING TECHSTREAM
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Ambient Temp Sensor Thermistor assembly Min.: -23.30°C (-9.94°F)
Max.: 65.95°C (150.71°F)
Actual ambient temperature displayed -
Body Electrical > Air Conditioner > Data List
Tester Display
Ambient Temp Sensor
50003 121 2
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
OK (When troubleshooting according to Problem Symptoms Table) A
OK (When troubleshooting according to the DTC) B
NG C



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

2.INSPECT COOLER (AMBIENT TEMPERATURE SENSOR) THERMISTOR
2.INSPECT COOLER (AMBIENT TEMPERATURE SENSOR) THERMISTOR
a.

Remove the cooler (ambient temperature sensor) thermistor.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AMBIENT TEMPERATURE SENSOR>REMOVAL


b.

Inspect the cooler (ambient temperature sensor) thermistor.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AMBIENT TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - COOLER [AMBIENT TEMPERATURE SENSOR] THERMISTOR)

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - COOLER [AMBIENT TEMPERATURE SENSOR] THERMISTOR)
a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the A26 cooler (ambient temperature sensor) thermistor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-35 (TX1+) - A26-2 (SO+) Always Below 1 Ω
G16-34 (TX1-) - A26-1 (SO-) Always Below 1 Ω
G16-35 (TX1+) - Body ground Always 10 kΩ or higher
G16-34 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL

HINT:

Since the combination meter assembly cannot be inspected while it is removed from the vehicle, replace the combination meter assembly with a new or known good one and check that the condition returns to normal.



b.

Check for DTCs.

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Proceed to
DTC B1412 is not output
DTC B1412 is output



DTC B1412 is not output

END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

DTC B1412 is output

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY