Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type)
RM30B0U _56 Audio / Visual / Telematics _009403 AUDIO / VIDEO _0054849 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Reverse Signal Circuit  


DESCRIPTION

The radio and display receiver assembly a reverse signal from the park/neutral position switch assembly to use for adjusting the vehicle position on the display.

WIRING DIAGRAM

E271823
4.698,1.76 5.313,1.958 0.615,0.198 10 false G143 4.708,1.938 7.083,2.156 2.375,0.219 10 false Radio and Display Receiver Assembly 5.385,1.177 5.844,1.375 0.458,0.198 10 false REV 5.177,1.083 5.333,1.281 0.156,0.198 10 false 2 3.708,1.073 4.021,1.271 0.313,0.198 10 false RL 3.969,1.063 4.125,1.26 0.156,0.198 10 false 2 3.021,1.063 3.333,1.26 0.313,0.198 10 false RB 2.823,1.052 2.979,1.25 0.156,0.198 10 false 1 2.74,1.542 3.198,1.74 0.458,0.198 10 false B36 2.729,1.74 4.052,2.125 1.323,0.385 10 false Park/Neutral Position Switch Assembly 0.188,1.188 1.448,1.458 1.26,0.271 10 false from GAUGE Fuse

CAUTION / NOTICE / HINT

NOTICE:

After replacing the radio and display receiver assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary (w/ SDARS System).


PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E270655

Enter the "Function Check/Setting I" mode and select "Vehicle Signal".

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>OPERATION CHECK


b.

Check that the display changes between ON and OFF according to the shift lever position.

OK:
Shift Lever Position Display
R ON
Except R OFF


HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (REVERSE SIGNAL)
2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (REVERSE SIGNAL)
a.
E140414
1.427,0.448 2.031,0.729 0.604,0.281 0.917,1.396 0.635,1.208 0.635,1.208 0.521,1.208 false 0.063,0.063 0.302,0.25 0.24,0.188 10 *a 1.573,0.5 1.938,0.688 0.365,0.188 10 G143 0.156,1.135 0.49,1.302 0.333,0.167 10 REV
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G143-2 (REV) - Body ground Ignition switch ON, shift lever in R 11 to 14 V
G143-2 (REV) - Body ground Ignition switch ON, shift lever any position other than in R Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the G143 radio and display receiver assembly connector.


b.

Disconnect the B36 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-2 (REV) - B36-2 (RL) Always Below 1 Ω
G143-2 (REV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)
a.
E270424
1.479,0.281 1.885,0.51 0.406,0.229 1.073,1.771 1.26,1.771 1.26,1.771 1.604,1.135 true 1.542,0.313 2,0.51 0.458,0.198 10 B36 0.823,1.698 1.281,1.896 0.458,0.198 10 RB 0.104,0.083 0.563,0.281 0.458,0.198 10 *a
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B36-1 (RB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR