Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM30B0U _58 Vehicle Interior _010070 LIGHTING (INT) _0054852 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  IG Signal Circuit  


DESCRIPTION

This circuit detects whether the ignition switch is ON or off, and sends this information to the main body ECU (Multiplex Network Body ECU).

WIRING DIAGRAM

E271431
5.99,0.594 6.229,0.792 0.24,0.198 10 false IG 4.167,1.5 5.115,1.708 0.948,0.208 10 false ECU-IG NO.2 3.604,0.604 3.917,0.802 0.313,0.198 10 false 3D 3.625,0.427 3.938,0.625 0.313,0.198 10 false 40 3.604,1.344 3.917,1.542 0.313,0.198 10 false 3C 3.604,1.167 3.917,1.365 0.313,0.198 10 false 15 3.615,1.906 3.927,2.104 0.313,0.198 10 false 3A 3.646,1.729 3.823,1.948 0.177,0.219 11 false 1 3.604,2.229 3.917,2.427 0.313,0.198 10 false 3C 3.615,2.073 3.927,2.271 0.313,0.198 10 false 43 3.604,3.021 3.917,3.219 0.313,0.198 10 false 3D 3.656,2.854 3.813,3.052 0.156,0.198 10 false 9 1.927,1.885 2.76,2.125 0.833,0.24 10 false from Battery 0.594,2.198 2.708,2.615 2.115,0.417 10 false from Certification ECU (Smart Key ECU Assembly)*1 0.573,2.76 2.135,2.969 1.563,0.208 10 false from Ignition Switch*2 3.917,3.75 5.583,4.167 1.667,0.417 10 false Instrument Panel Junction Block Assembly 4.75,4.635 6.927,5.052 2.177,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 4.76,4.469 4.917,4.667 0.156,0.198 10 false A 0.167,5.042 2.083,5.25 1.917,0.208 10 false *1: w/ Smart Key System 0.167,5.333 2.177,5.531 2.01,0.198 10 false *2: w/o Smart Key System 5.76,0.49 6.073,0.688 0.313,0.198 10 false 32 4.438,2.51 5.104,2.729 0.667,0.219 10 false IG1 NO.1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING TECHSTREAM (IG SW)
a.

Using the Techstream, read the Data List.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG SW ignition switch ON signal ON or OFF ON: ignition switch ON
OFF: ignition switch off
"OFF" is also displayed for this item when the ignition switch is ACC.
Body Electrical > Main Body > Data List
Tester Display
IG SW
50003 123 30
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
a.
E270693
0.792,0.781 1.208,1.042 0.417,0.26 0.292,2.094 0.708,2.354 0.417,0.26 0.229,3.604 0.646,3.865 0.417,0.26 0.156,0.125 0.469,0.281 0.313,0.156 10 *a 0.917,0.833 1.229,0.99 0.313,0.156 10 3A 0.354,3.646 0.667,3.802 0.313,0.156 10 3D 0.417,2.135 0.729,2.292 0.313,0.156 10 3C
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the instrument panel junction block assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3A-1 - Body ground Always 11 to 14 V
3C-43 - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-9 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY CIRCUIT)
a.

Disconnect the 3C and 3D instrument panel junction block assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-15 - 3D-40 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO.1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO.1 RELAY)
a.
E270709
0.854,0.469 1.281,0.75 0.427,0.281 0.115,1.667 0.542,1.948 0.427,0.281 0.083,2.99 0.51,3.271 0.427,0.281 1.49,3.615 1.917,3.896 0.427,0.281 2.792,4.354 2.99,4.104 false 0.979,0.531 1.292,0.729 0.313,0.198 10 3A 0.25,1.729 0.563,1.927 0.313,0.198 10 3C 0.229,3.063 0.542,3.26 0.313,0.198 10 3D 1.656,3.667 1.969,3.865 0.313,0.198 10 A 2.646,4.313 2.958,4.51 0.313,0.198 10 IG

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3A-1 - 3C-15 Battery voltage applied between terminals 3C-43 and 3D-9 Below 1 Ω
Battery voltage not applied between terminals 3C-43 and 3D-9 10 kΩ or higher
A-32 (IG) - 3D-40 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY