The main body ECU (Multiplex Network Body ECU) controls the ignition key cylinder light (w/o Smart Key System), map light and No. 1 room light.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Using the Techstream, perform the Active Test.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Illuminated Entry System | Map light, ignition key cylinder light (w/o Smart Key System) and No. 1 room light | ON or OFF | Turn the map light switch and No. 1 room light switch to the DOOR position. |
| Tester Display |
|---|
| Illuminated Entry System |
| Result | Proceed to |
|---|---|
| Map light assembly, No. 1 room light assembly and ignition key cylinder light comes on | A |
| Map light assembly and No. 1 room light assembly does not comes on | B |
| Map light assembly or No. 1 room light assembly does not comes on | C |
| Ignition key cylinder light does not comes on (w/o Smart Key System) | D |
A
B
C
D
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Inspect the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | w/ Sliding Roof System |
| *B | w/o Sliding Roof System |
Disconnect the map light assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q12-3 (+B1) - Body ground | Battery saving control (interior light auto cut function) not operating | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q11-3 (+B1) - Body ground | Battery saving control (interior light auto cut function) not operating | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q12-1 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q11-1 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Q12*1 or Q11*2 map light assembly connector.
*1: w/ Sliding Roof System
*2: w/o Sliding Roof System
Disconnect the 3D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q12-2 (CTY) - 3D-35 | Always | Below 1 Ω |
| Q12-2 (CTY) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q11-2 (CTY) - 3D-35 | Always | Below 1 Ω |
| Q11-2 (CTY) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 (ILE) - 3D-35 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the transponder key coil (ignition key cylinder light).
Click hereVehicle Interior>LIGHTING (INT)>IGNITION KEY CYLINDER LIGHT>REMOVAL
Inspect the transponder key coil (ignition key cylinder light).
Click hereVehicle Interior>LIGHTING (INT)>IGNITION KEY CYLINDER LIGHT>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G6 transponder key coil (ignition key cylinder light) connector.
Disconnect the 3D instrument panel junction block assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G6-2 (ILL+) - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G6-4 (ILL-) - 3D-44 | Always | Below 1 Ω |
| G6-4 (ILL-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-26 (KILE) - 3D-44 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG