Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM30B0U _58 Vehicle Interior _010070 LIGHTING (INT) _0054852 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Auto Cut Circuit  


DESCRIPTION

The main body ECU (Multiplex Network Body ECU) controls the DOME CUT relay.

WIRING DIAGRAM

E270025
0.188,0.667 1.115,0.885 0.927,0.219 10 from Battery 4.917,2.938 7.083,3.385 2.167,0.448 10 Main Body ECU (Multiplex Network Body ECU) 4.938,2.771 5.406,2.958 0.469,0.188 10 G78 5.854,0.906 6.198,1.094 0.344,0.188 10 15 6.125,1 6.594,1.188 0.469,0.188 10 DOMR 3.552,0.615 3.75,0.792 0.198,0.177 10 3 3.552,0.917 3.75,1.094 0.198,0.177 10 1 2.792,0.615 2.99,0.792 0.198,0.177 10 5 2.802,0.917 3,1.094 0.198,0.177 10 2 2.833,1.302 3.76,1.521 0.927,0.219 10 DOME CUT 1.448,0.875 1.969,1.094 0.521,0.219 10 DOME 1.344,2.281 2.469,2.49 1.125,0.208 10 to Interior Lights

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING TECHSTREAM (DOME CUT RELAY)
a.

Using the Techstream, read the Data List.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Relay for Interior Light Auto Cut Function DOME CUT relay ON or OFF -
Body Electrical > Main Body > Active Test
Tester Display
Relay for Interior Light Auto Cut Function
50004 123 66
OK:

Battery saving control (interior light auto cut function) operates.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT DOME CUT RELAY
2.INSPECT DOME CUT RELAY
a.
E270015
2.5,1.125 2.875,0.979 false 2.51,1.365 2.885,1.323 false 2.583,0.802 2.865,0.531 false 2,0.49 2.208,0.813 false 0.552,0.729 0.708,0.927 0.156,0.198 10 5 0.552,1.281 0.708,1.479 0.156,0.198 10 2 1.708,0.729 1.865,0.927 0.156,0.198 10 3 1.688,1.271 1.844,1.469 0.156,0.198 10 1 1.865,0.365 2.021,0.563 0.156,0.198 10 1 2.906,0.385 3.063,0.583 0.156,0.198 10 2 2.938,0.865 3.094,1.063 0.156,0.198 10 5 2.948,1.24 3.104,1.438 0.156,0.198 10 3

Remove the DOME CUT relay from the No. 5 relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BATTERY - DOME CUT RELAY)

NG

REPLACE DOME CUT RELAY

3.CHECK HARNESS AND CONNECTOR (BATTERY - DOME CUT RELAY)
a.
E270849
0.167,0.135 0.479,0.333 0.313,0.198 10 *a
*a Front view of wire harness connector
(to DOME CUT Relay)


Remove the DOME CUT relay from the No. 5 relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
DOME CUT relay terminal 2 - Body ground Always 11 to 14 V
DOME CUT relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (DOME CUT RELAY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DOME CUT RELAY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Remove the DOME CUT relay from the No. 5 relay block.


b.

Disconnect the G78 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DOME CUT relay terminal 1 - G78-15 (DOMR) Always Below 1 Ω
G78-15 (DOMR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR