Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM30B0U _59 Vehicle Exterior _010071 LIGHTING (EXT) _0054853 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B1244  Light Sensor Circuit Malfunction  


DESCRIPTION

The automatic light control sensor detects ambient light, converts it into an electrical signal and outputs it to the main body ECU (Multiplex Network Body ECU). The main body ECU (Multiplex Network Body ECU) turns the headlights and taillights on or off according to the signal.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1244 Light Sensor Circuit Malfunction
·

Malfunction in the automatic light control sensor.

·

Open or short in the automatic light control sensor circuit.


·

Automatic light control sensor

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

E240319
0.24,2.729 0.573,2.906 0.333,0.177 10 G2 0.24,2.875 2.26,3.083 2.021,0.208 10 Automatic Light Control Sensor 5.313,2.719 5.646,2.896 0.333,0.177 10 G78 5.323,2.885 6.948,3.292 1.625,0.406 10 Main Body ECU (Multiplex Network Body ECU) 1.104,1.417 1.51,1.615 0.406,0.198 10 CLTB 1.104,2.208 1.51,2.406 0.406,0.198 10 CLTS 1.104,0.583 1.51,0.781 0.406,0.198 10 CLTE 5.667,1.396 6.073,1.594 0.406,0.198 10 CLTB 5.667,2.177 6.073,2.375 0.406,0.198 10 CLTS 5.667,0.594 6.073,0.792 0.406,0.198 10 CLTE 5.375,1.292 5.635,1.469 0.26,0.177 10 20 5.375,2.094 5.563,2.26 0.188,0.167 10 21 5.375,0.479 5.635,0.667 0.26,0.188 10 22 1.625,1.292 1.813,1.458 0.188,0.167 10 6 1.625,2.094 1.813,2.26 0.188,0.167 10 5 1.625,0.5 1.813,0.667 0.188,0.167 10 3

PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

Result:
Proceed to
DTC B1244 output does not occur
DTC B1244 output occur



DTC B1244 output does not occur

DTC B1244 output occur

3.READ VALUE USING TECHSTREAM (AUTOMATIC LIGHT CONTROL SENSOR)
3.READ VALUE USING TECHSTREAM (AUTOMATIC LIGHT CONTROL SENSOR)
a.

Using the Techstream, read the Data List.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Illumination Rate Info Illumination rate information 0 ms. to 2162.65 ms. Value output according to ambient light levels -
Body Electrical > Main Body > Data List
Tester Display
Illumination Rate Info
50003 123 61
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - AUTOMATIC LIGHT CONTROL SENSOR)
4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - AUTOMATIC LIGHT CONTROL SENSOR)
a.

Disconnect the G78 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the G2 automatic light control sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G78-22 (CLTE) - G2-3 (CLTE) Always Below 1 Ω
G78-21 (CLTS) - G2-5 (CLTS) Always Below 1 Ω
G78-20 (CLTB) - G2-6 (CLTB) Always Below 1 Ω
G78-22 (CLTE) - Body ground Always 10 kΩ or higher
G78-21 (CLTS) - Body ground Always 10 kΩ or higher
G78-20 (CLTB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.
E203228
0.125,0.635 0.552,0.875 0.427,0.24 2.771,1.656 2.333,1.135 false 2.094,1.677 2.031,1.146 false 0.042,0.104 0.354,0.26 0.313,0.156 10 *a 1.917,1.708 2.375,1.896 0.458,0.188 10 CLTE 0.198,0.667 0.573,0.833 0.375,0.167 10 G78 2.677,1.698 3.135,1.885 0.458,0.188 10 CLTB
*a Component with harness connected
(Main Body ECU [Multiplex Network Body ECU])


Remove the instrument panel junction block assembly and main body ECU (multiplex network body ECU) as a unit with the connectors still connected.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G78-20 (CLTB) - G78-22 (CLTE) Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK AUTOMATIC LIGHT CONTROL SENSOR

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

6.CHECK AUTOMATIC LIGHT CONTROL SENSOR
a.

Check the automatic light control sensor.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC LIGHT CONTROL SENSOR>REMOVAL


Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR