Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM30B0U _59 Vehicle Exterior _010071 LIGHTING (EXT) _0054853 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Headlight Relay Circuit  


DESCRIPTION

The main body ECU (Multiplex Network Body ECU) receives headlight dimmer switch information signals and illuminates the low beam headlights.

WIRING DIAGRAM

E270106
4.729,2.656 6.323,3.115 1.594,0.458 10 false Instrument Panel Junction Block Assembly 3.052,1.302 3.979,1.5 0.927,0.198 10 false H-LP LH-LO 3.094,3.833 4.021,4.031 0.927,0.198 10 false H-LP RH-LO 3,0.219 3.896,0.448 0.896,0.229 10 false from Battery 0.938,4.344 2.292,4.583 1.354,0.24 10 false Headlight Unit RH 0.938,4.198 1.333,4.406 0.396,0.208 10 false A39 0.938,1.854 2.292,2.094 1.354,0.24 10 false Headlight Unit LH 0.938,1.708 1.333,1.917 0.396,0.208 10 false A18 0.979,1.073 1.188,1.281 0.208,0.208 10 false E 0.792,1.063 1,1.271 0.208,0.208 10 false 1 2.104,1.052 2.313,1.26 0.208,0.208 10 false LO 2.396,1.063 2.604,1.271 0.208,0.208 10 false 2 5.167,1.354 5.375,1.563 0.208,0.208 10 false 1 5.167,1.063 5.375,1.271 0.208,0.208 10 false 5 4.375,1.063 4.583,1.271 0.208,0.208 10 false 3 4.719,2.5 5,2.698 0.281,0.198 10 false 3B 5.458,1.938 5.74,2.135 0.281,0.198 10 false 37 6.177,1.948 6.458,2.146 0.281,0.198 10 false 15 6.427,2.052 6.885,2.26 0.458,0.208 10 false HRLY 4.958,4.917 5.417,5.198 0.458,0.281 10 false A 4.938,5.104 7.115,5.583 2.177,0.479 10 false Main Body ECU (Multiplex Network Body ECU) 0.979,3.573 1.188,3.781 0.208,0.208 10 false E 2.104,3.583 2.313,3.792 0.208,0.208 10 false LO 0.771,3.573 0.979,3.781 0.208,0.208 10 false 1 4.375,1.344 4.583,1.552 0.208,0.208 10 false 2 4.635,1.74 5.188,1.938 0.552,0.198 10 false H-LP 2.406,3.573 2.563,3.771 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the bulbs and fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (H-LP RELAY)
a.

Using the Techstream, perform the Active Test.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Headlight Relay Low beam headlight relay ON or OFF -
Body Electrical > Main Body > Active Test
Tester Display
Headlight Relay
50004 123 14
OK:

Headlight relay operates (low beam headlights come on).



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT HEADLIGHT RELAY (H-LP)
2.INSPECT HEADLIGHT RELAY (H-LP)
a.
E234221
2.146,1.771 2.49,1.427 false 2.479,0.719 2.823,0.375 false 3.208,1.083 2.833,1.083 false 2.083,1.083 1.708,1.083 false 0.469,0.719 0.583,0.875 0.115,0.156 10 3 0.469,1.281 0.583,1.438 0.115,0.156 10 2 1.271,0.719 1.385,0.875 0.115,0.156 10 5 1.271,1.281 1.385,1.438 0.115,0.156 10 1 3.229,1.01 3.344,1.167 0.115,0.156 10 5 2.854,0.25 2.969,0.406 0.115,0.156 10 1 1.615,1 1.729,1.156 0.115,0.156 10 3 2.031,1.698 2.146,1.854 0.115,0.156 10 2

Remove the headlight relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage applied between terminals 1 and 2 Below 1 Ω
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP] - BATTERY)

NG

REPLACE HEADLIGHT RELAY (H-LP)

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP] - BATTERY)
a.
E271422
0.073,0.052 0.385,0.25 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Headlight Relay)


Remove the headlight relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Headlight relay terminal 5 - Body ground Always 11 to 14 V
Headlight relay terminal 1 - Body ground



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP] - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP] - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Remove the headlight relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the 3B instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Headlight relay terminal 2 - 3B-37 Always Below 1 Ω
3B-37 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.
E270896
1.479,2.281 1.917,2.531 0.438,0.25 0.063,1.01 0.406,1.26 0.344,0.25 1.615,3.042 1.615,2.823 false 0.135,1.052 0.448,1.25 0.313,0.198 10 3B 1.469,3.063 1.906,3.26 0.438,0.198 10 HRLY 1.656,2.323 1.969,2.521 0.313,0.198 10 A

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-15 (HRLY) - 3B-37 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY