Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM30B0U _58 Vehicle Interior _009409 SEAT _0054863 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2653  Lifter Sensor Malfunction  


DESCRIPTION

When the position control ECU and switch assembly does not receive a sensor signal despite upward or downward movement of the seat by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2653 Lifter Sensor Malfunction The upward and downward lock detection position of the sensor is the same.
·

Position control ECU and switch assembly

·

Lifter motor (Separate type front seat cushion spring assembly)

·

Harness or connector



WIRING DIAGRAM

B342142
4.729,3.875 6.813,4.521 2.083,0.646 10 Position Control ECU and Switch Assembly 0.781,3.854 2.906,4.479 2.125,0.625 10 Separate Type Front Seat Cushion Spring Assembly 1.302,3.083 1.76,3.281 0.458,0.198 10 e14 1.313,3.271 2.292,3.583 0.979,0.313 10 Lifter Motor 2.26,1.073 2.417,1.271 0.156,0.198 10 4 2.229,1.573 2.385,1.771 0.156,0.198 10 1 2.24,2.083 2.448,2.323 0.208,0.24 10 2 2.229,2.573 2.385,2.771 0.156,0.198 10 3 4.802,1.198 5.26,1.396 0.458,0.198 10 e18 4.802,1.698 5.26,1.896 0.458,0.198 10 e18 4.844,2.198 5.156,2.396 0.313,0.198 10 e6 4.844,2.698 5.156,2.896 0.313,0.198 10 e6 4.854,0.979 5.177,1.188 0.323,0.208 10 10 4.854,1.5 5.167,1.677 0.313,0.177 10 12 4.896,1.979 5.052,2.177 0.156,0.198 10 4 4.896,2.51 5.042,2.708 0.146,0.198 10 1 5.177,1.198 5.792,1.396 0.615,0.198 10 LFT+ 5.167,1.688 5.781,1.885 0.615,0.198 10 LET- 5.135,2.188 5.75,2.385 0.615,0.198 10 SSRL 5.146,2.708 5.76,2.906 0.615,0.198 10 SGND

PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (LIFTER MOTOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the Techstream.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Lifter Operation Seat lifter operation OFF/Down/Up -
Body Electrical > Driver Seat > Active Test
Tester Display
Lifter Operation
50004 162 2
OK:

Motor operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (LIFTER MOTOR CIRCUIT)

NG

5.INSPECT LIFTER MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)
2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (LIFTER MOTOR CIRCUIT)
a.
E118523
1.552,0.344 1.885,0.583 0.333,0.24 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.615,0.375 1.979,0.594 0.365,0.219 10 false e14
*a Front view of wire harness connector
(to Lifter Motor [Separate Type Front Seat Cushion Spring Assembly])


Disconnect the e14 lifter motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
e14-2 - e14-3 Lifter switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

3.CHECK LIFTER MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - LIFTER MOTOR)
3.CHECK LIFTER MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)
a.
B238515
1.552,0.323 1.927,0.573 0.375,0.25 0.125,0.073 0.469,0.427 0.344,0.354 10 *a 1.667,0.365 2.167,0.615 0.5,0.25 10 e14
*a Component with harness connected
(Lifter Motor [Separate Type Front Seat Cushion Spring Assembly])


Reconnect the e14 lifter motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
e14-2 - Body ground Lifter switch on 4.5 to 4.8 V



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPLACE LIFTER MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - LIFTER MOTOR)
a.

Disconnect the e6 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e6-4 (SSRL) - e14-2 Always Below 1 Ω
e6-1 (SGND) - e14-3 Always Below 1 Ω
e6-4 (SSRL) - Body ground Always 10 kΩ or higher
e6-1 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT LIFTER MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)
a.

Remove the separate type front seat cushion spring assembly.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY


b.

Inspect the separate type front seat cushion spring assembly.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - LIFTER MOTOR)

NG

REPLACE LIFTER MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - LIFTER MOTOR)
a.

Disconnect the e18 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e18-10 (LFT+) - e14-4 Always Below 1 Ω
e18-12 (LFT-) - e14-1 Always Below 1 Ω
e18-10 (LFT+) - Body ground Always 10 kΩ or higher
e18-12 (LFT-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR