When a door is unlocked using the wireless unlock function*1 or entry unlock function*2, the certification ECU (smart key ECU assembly) sends a door unlock signal and key ID signal to the main body ECU (multiplex network body ECU). When the main body ECU (multiplex network body ECU) receives the door unlock signal, it stores the key ID. When the driver door is opened, the memory call and memory command information of the stored key ID is sent to each driving position related control ECU. Each control ECU receives the memory commands and performs the memory call operation according to predetermined control timing values.
*1: w/o Smart Key System
*2: w/ Smart Key System
The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there is no malfunction in the communication system by checking communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING
Check the operation of the power seats.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Check whether seat positions can be stored in memory.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Check whether seat positions can be restored.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Check the operation of memory call registration.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
| Result | Proceed to |
|---|---|
| OK | A |
| NG (power seat operation) | B |
| NG (seat position memory) | C |
| NG (seat position restoring) | D |
| NG (memory call registration) | E |
A
B
C
D
E
Turn the ignition switch off.
Close and lock all doors.
Unlock the driver door by pressing the unlock switch of the memory call registered key (wireless unlock function).
Unlock the driver door by touching the driver door outside handle while holding the memory call registered key (entry unlock function).
Open the driver door and check that the driver seat moves to the memorized position.
| Result | Proceed to |
|---|---|
| Memory call function linked with the wireless unlock function does not operate. (w/o Smart Key System) | A |
| Memory call function linked with the entry unlock function does not operate. (w/ Smart Key System) | B |
A
B
Check the wireless unlock function.
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Key System)>OPERATION CHECK
Wireless unlock function is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the entry unlock function of the smart key system.
Entry unlock function is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the position control ECU and switch assembly.
Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Store a seat position in memory.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Perform memory call registration.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Turn the ignition switch off.
Close and lock all doors.
Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle while holding the memory call registered key.
Open the driver door and check that the driver seat moves to the memorized position.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Driver seat moves to the memorized position.
| Proceed to |
|---|
| OK |
| NG |
OK
NG