Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
1.CLEAN QUARTER WINDOW ASSEMBLY LH
Clean the outer circumference of the quarter window assembly with a non-residue solvent.
Do not touch the quarter window assembly surface after cleaning it.
Be careful not to damage the quarter window assembly and clips.
2.INSTALL QUARTER WINDOW ASSEMBLY LH
| *1 | Primer M |
| *2 | Adhesive |
| *a | CORRECT |
| *b | INCORRECT |
|
Primer M |
Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.
Allow the Primer M coating to dry for 3 minutes or more.
Throw away any leftover primer.
Do not apply too much primer.
Using a brush or sponge, apply Primer G to the contact surface of the new quarter window assembly.
| *A | Back Side | - | - |
| *1 | Adhesive Center Line | - | - |
|
Primer G | - | - |
If primer is applied to an area that is not specified, wipe off the primer with non-residue solvent before it dries.
Allow the primer to dry for 3 minutes or more.
Throw away any leftover primer.
Do not apply too much primer.
| Area | Specified Condition |
|---|---|
| a | 11 mm (0.4331 in.) |
| b | 24.9 mm (0.9803 in.) |
| c | 13.4 mm (0.5276 in.) |
Apply adhesive to the quarter window assembly.
Toyota Genuine Windshield Glass Adhesive or Equivalent or equivalent
Cut off the tip of the cartridge nozzle as shown in the illustration.
| *A | Back Side | - | - |
| *1 | Adhesive | *2 | Adhesive Center Line |
| Area | Specified Condition |
|---|---|
| a | 8.0 mm (0.3150 in.) |
| b | 12.0 mm (0.4724 in.) |
| c | 5.9 mm (0.2323 in.) |
| d | 2.4 mm (0.0945 in.) |
After cutting off the tip, use all adhesive within the time written in the table below.
| Temperature | Usage Time Frame |
|---|---|
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with the cartridge.
Apply adhesive to the quarter window assembly as shown in the illustration.
Install the quarter window assembly to the vehicle body.
Hold the quarter window assembly in place securely with protective tape or equivalent until the adhesive hardens.
Allow the primer coating to dry for 3 minutes or more.
Check that the clips are attached to the body correctly.
Check the clearance between the body and glass.
Lightly press the front surface of the glass to ensure a close fit.
| *1 | Adhesive |
Using a scraper, remove any excess or protruding adhesive.
Apply adhesive to the glass rim.
Do not drive the vehicle within the time written in the table below.
| Temperature | Minimum Time Prior to Driving Vehicle |
|---|---|
| 35°C (95°F) | 1 hour 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
3.CHECK FOR LEAKS AND REPAIR
Conduct a leak test after the adhesive has completely hardened.
Seal any leaks with auto glass sealer.
4.INSTALL ROOF HEADLINING ASSEMBLY
5.INSTALL INNER ROOF SIDE GARNISH ASSEMBLY RH
6.INSTALL INNER ROOF SIDE GARNISH ASSEMBLY LH
7.INSTALL SEAT BELT ANCHOR COVER CAP
8.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
9.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
10.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
11.INSTALL REAR DOOR SCUFF PLATE LH
12.INSTALL REAR SEAT ASSEMBLY LH
13.INSTALL REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE
14.INSTALL REAR DECK TRIM COVER (for Full Size Spare Tire)
15.INSTALL REAR FLOOR FINISH PLATE (for Compact Spare Tire)
16.INSTALL DECK FLOOR BOX LH
17.INSTALL DECK BOARD ASSEMBLY (for Full Size Spare Tire)
18.INSTALL DECK BOARD ASSEMBLY
19.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
20.INSTALL PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY (w/ Partition Net)