Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM30B0U _55 Steering _010121 POWER ASSIST SYSTEMS _0054952 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1551/25  IG Power Supply Voltage Malfunction  


DESCRIPTION

The power steering ECU assembly distinguishes the ignition switch status as ON or off through the IG power source circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition
C1551/25 IG Power Supply Voltage Malfunction IG power source circuit malfunction inside ECU
·

EPS-IG fuse

·

IG power source circuit

·

ECU wire sub-assembly

·

Power steering ECU assembly


On Ignition switch ON again

WIRING DIAGRAM

C250100
0.75,1.042 1.792,1.26 1.042,0.219 10 false from IG Circuit 2.208,1.198 3.083,1.625 0.875,0.427 10 false EPS-IG 3.385,1.042 3.719,1.365 0.333,0.323 10 false hG1 5.083,1.031 5.646,1.396 0.563,0.365 10 false IG 3.469,0.844 3.781,1.115 0.313,0.271 10 false 5 4.781,0.833 5.104,1.156 0.323,0.323 10 false 1 4.781,1.938 5.167,2.208 0.385,0.271 10 false 2 5.083,2.146 5.792,2.5 0.708,0.354 10 false PGND 4.865,2.938 7.135,3.323 2.271,0.385 10 false Power Steering ECU Assembly 4.792,1.031 5.365,1.344 0.573,0.313 10 false h1 4.781,2.135 5.219,2.448 0.438,0.313 10 false h2 4.146,1.177 4.708,1.594 0.563,0.417 10 false * 4.198,2.292 4.583,2.656 0.385,0.365 10 false * 0.292,3.271 2.25,3.635 1.958,0.365 10 false *: ECU Wire Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly has been replaced, perform assist map writing (Click here Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION AND GROUND WIRE
a.

Check the connection condition of the ECU wire sub-assembly and power steering ECU assembly connectors.

OK:

The ECU wire sub-assembly and power steering ECU assembly connectors are securely connected.



b.

Check that the ground wire is securely installed with the bolt.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>INSTALLATION

OK:

The ground wire is securely installed with the bolt.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING TECHSTREAM (IG POWER SUPPLY)

NG

CONNECT CONNECTOR OR INSTALL GROUND WIRE

2.READ VALUE USING TECHSTREAM (IG POWER SUPPLY)
a.

Turn the ignition switch off.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the Techstream on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Select the item "IG power supply" in the Data List and read the value displayed on the Techstream.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG Power Supply ECU power source voltage Min.: 0.0000 V
Max.: 20.1531 V
Ignition switch ON: 11 to 14 V -
Chassis > EMPS > Data List
Tester Display
IG Power Supply
50003 142 11
OK:

The normal condition value is displayed on the Techstream.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY)
3.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY)
a.
C278679
0.729,0.635 1.167,0.938 0.438,0.302 1.958,1.406 2.51,1.427 false 2.594,1.365 2.906,1.615 0.313,0.25 10 IG 0.833,0.708 1.146,0.906 0.313,0.198 10 hG1 0.135,0.094 0.448,0.25 0.313,0.156 10 *a
*a Front view of wire harness connector
(to ECU Wire Sub-assembly)


Disconnect the hG1 ECU wire sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
hG1-5 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK ECU WIRE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ECU WIRE SUB-ASSEMBLY
a.
C240351
0.344,3.271 0.792,3.552 0.448,0.281 0.604,0.906 1.052,1.188 0.448,0.281 2.271,3.531 2.354,4.135 false 1.115,1.677 1.49,1.802 false 0.198,0.146 0.635,0.458 0.438,0.313 10 *a 0.51,3.333 0.948,3.729 0.438,0.396 10 h2 2.177,4.177 2.906,4.51 0.729,0.333 10 PGND 0.917,1.583 1.344,1.948 0.427,0.365 10 IG 0.771,0.969 1.156,1.354 0.385,0.385 10 h1
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Connect the hG1 connector to the ECU wire sub-assembly.


b.

Disconnect the h1 and h2 power steering ECU assembly connectors.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
h1-1 (IG) - Body ground Ignition switch ON 11 to 14 V



e.

Turn the ignition switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h2-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE ECU WIRE SUB-ASSEMBLY