Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM30B0U _55 Steering _010121 POWER ASSIST SYSTEMS _0054952 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1552/22  PIG Power Supply Voltage Malfunction  C1554/23  Power Supply Relay Failure  


DESCRIPTION

When a problem occurs in the power steering system, the power source relay circuit is shut off to stop the power assist.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition
C1552/22 PIG Power Supply Voltage Malfunction PIG power source circuit malfunction inside ECU
·

EPS fuse

·

PIG power source circuit

·

ECU wire sub-assembly

·

Power steering ECU assembly


On Ignition switch ON again
C1554/23 Power Supply Relay Failure Power source relay circuit malfunction
·

EPS fuse

·

PIG power source circuit

·

ECU wire sub-assembly

·

Power steering ECU assembly


On Ignition switch ON again

WIRING DIAGRAM

C277339
4.958,3.146 6.979,3.458 2.021,0.313 10 false Power Steering ECU Assembly 4.948,2.969 5.198,3.167 0.25,0.198 10 false h2 4.313,2.115 4.563,2.313 0.25,0.198 10 false * 4.26,0.667 4.51,0.865 0.25,0.198 10 false * 3.75,0.823 4.125,1.031 0.375,0.208 10 false Ah1 3.823,0.604 4.073,0.802 0.25,0.198 10 false 1 2.667,0.979 3.094,1.219 0.427,0.24 10 false EPS 0.542,0.802 1.479,1.052 0.938,0.25 10 false from Battery 5.177,0.833 5.51,1.042 0.333,0.208 10 false PIG 5.167,2.281 5.677,2.469 0.51,0.188 10 false PGND 4.833,2.125 5.083,2.323 0.25,0.198 10 false 2 4.813,0.677 5.063,0.875 0.25,0.198 10 false 1 0.26,3.229 2.281,3.469 2.021,0.24 10 false *: ECU Wire Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly has been replaced, perform assist map writing (Click here Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION AND GROUND WIRE
a.

Check the connection condition of the ECU wire sub-assembly and power steering ECU assembly connectors.

OK:

The ECU wire sub-assembly and power steering ECU assembly connectors are securely connected.



b.

Check that the ground wire is securely installed with the bolt.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>INSTALLATION

OK:

The ground wire is securely installed with the bolt.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING TECHSTREAM (PIG POWER SUPPLY)

NG

CONNECT CONNECTOR OR INSTALL GROUND WIRE

2.READ VALUE USING TECHSTREAM (PIG POWER SUPPLY)
a.

Turn the ignition switch off.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the Techstream on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Select the item "PIG Power Supply" in the Data List and read the value displayed on the Techstream.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
PIG Power Supply Power source voltage to active motor Min.: 0.0000 V
Max.: 20.1531 V
Engine running and steering wheel being turned: 11 to 14 V -
Chassis > EMPS > Data List
Tester Display
PIG Power Supply
50003 142 10
OK:

The normal condition value is displayed on the Techstream.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (BATTERY - ECU WIRE SUB-ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (BATTERY - ECU WIRE SUB-ASSEMBLY)
a.
C277337
0.594,0.781 1.042,1.125 0.448,0.344 1.813,1.229 2.417,0.99 false 0.146,0.104 0.458,0.333 0.313,0.229 10 *a 2.51,0.917 2.917,1.177 0.406,0.26 10 PIG 0.708,0.875 1.167,1.146 0.458,0.271 10 Ah1
*a Front view of wire harness connector
(to ECU Wire Sub-assembly)


Disconnect the Ah1 ECU wire sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Ah1-1 (PIG) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK ECU WIRE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ECU WIRE SUB-ASSEMBLY
a.
C240344
0.229,1 0.677,1.281 0.448,0.281 2.146,1.188 2.229,1.781 false 1.198,1.198 1.115,1.792 false 0.146,0.125 0.74,0.552 0.594,0.427 10 *a 0.396,1.052 0.854,1.375 0.458,0.323 10 h2 2.094,1.833 2.896,2.177 0.802,0.344 10 PGND 1.021,1.823 1.521,2.146 0.5,0.323 10 PIG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Connect the Ah1 connector to the ECU wire sub-assembly.


b.

Disconnect the h2 power steering ECU assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
h2-1 (PIG) - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h2-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE ECU WIRE SUB-ASSEMBLY