The radio and display receiver assembly and stereo component amplifier assembly are connected by the AVC-LAN communication line.
This DTC is stored when an AVC-LAN communication error occurs between the radio and display receiver assembly and stereo component amplifier assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15D3 | Stereo Component Amplifier Disconnected | When either condition below is met:
·
Stereo component amplifier assembly is/was not connected while the ignition switch is/was ON or ACC. ·
Communication between the master unit and the stereo component amplifier assembly is not possible when the engine is started. |
·
Stereo component amplifier assembly ·
Radio and display receiver assembly ·
Harness or connector |
The radio and display receiver assembly is the master unit.
After replacing the radio and display receiver assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary (w/ SDARS System).
Inspect the fuses for circuits related to this system before performing the following procedure.
If DTC B15C3 is output, perform troubleshooting for DTC B15C3 first.
| Proceed to |
|---|
| DTC B15C3 is not output |
| DTC B15C3 is output |
DTC B15C3 is not output
DTC B15C3 is output
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>B15C3
Check that optional components (including associated wiring) which generate radio waves are not installed.
| Result | Proceed to |
|---|---|
| Optional components (including associated wiring) are installed | A |
| Optional components (including associated wiring) are not installed | B |
Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.
A
B
Remove optional components (including associated wiring).
Do not remove optional components or associated wiring without the permission of the customer.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
| Proceed to |
|---|
| No DTCs are output |
| DTCs are output |
No DTCs are output
DTCs are output
| *a | Front view of wire harness connector
(for Stereo Component Amplifier Assembly) |
Disconnect the stereo component amplifier assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M23-3 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M23-1 (+B) - Body ground | Always | 11 to 14 V |
| M22-12 (ACC) - Body ground | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G67 radio and display receiver assembly connector.
Disconnect the M22 stereo component amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G67-5 (TX2+) - M22-8 (TX+) | Always | Below 1 Ω |
| G67-15 (TX2-) - M22-7 (TX-) | Always | Below 1 Ω |
| G67-5 (TX2+) - Body ground | Always | 10 kΩ or higher |
| G67-15 (TX2-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the stereo component amplifier assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
| Proceed to |
|---|
| No DTCs are output |
| DTCs are output |
No DTCs are output
DTCs are output