Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)
RM30B0U _58 Vehicle Interior _009988 HEATING / AIR CONDITIONING _0054779 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1422  Compressor Lock Sensor Circuit  


DESCRIPTION

The ECM sends the engine speed signal to the air conditioning amplifier assembly via CAN communication.

The air conditioning amplifier assembly reads the difference between compressor speed and engine speed. When the difference becomes too large, the air conditioning amplifier assembly determines that the compressor is locked, and turns the magnet clutch off.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1422 Compressor Lock Sensor Circuit Open or short in A/C lock sensor circuit
·

Cooler compressor assembly (A/C lock sensor)

·

Compressor drive belt

·

Harness or connector

·

Air conditioning amplifier assembly

·

CAN communication system


- w/ Magnet Clutch

HINT:

The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E226603
0.677,1.615 1.354,1.979 0.677,0.365 10 false ECM 0.74,3.813 2.823,4.24 2.083,0.427 10 false : CAN Communication Line 5.958,1.885 6.635,2.302 0.677,0.417 10 false LOCK 5.958,3.052 6.729,3.479 0.771,0.427 10 false SG-2 4.177,1.781 4.563,2.135 0.385,0.354 10 false 1 2.844,1.771 3.313,2.177 0.469,0.406 10 false 2 2.781,2.406 4.469,2.781 1.688,0.375 10 false Magnet Clutch Assembly (A/C Lock Sensor) 5.74,3.667 7.115,4.115 1.375,0.448 10 false Air Conditioning Amplifier Assembly 5.656,1.792 5.948,1.99 0.292,0.198 10 false 21 5.74,2.938 5.927,3.115 0.188,0.177 10 false 5 2.781,2.229 3.302,2.5 0.521,0.271 10 false B68 5.729,3.49 6.052,3.823 0.323,0.333 10 false G80 3.729,1.781 4.125,1.938 0.396,0.156 10 false SSR+ 3.021,1.781 3.417,1.938 0.396,0.156 10 false SSR-

CAUTION / NOTICE / HINT

NOTICE:

Before performing the inspection, check that there are no problems related to the CAN communication system.


HINT:

As DTC B1422/22 is also output when the compressor drive belt is damaged or loose, inspect the belt before performing troubleshooting.


PROCEDURE

1.INSPECT COOLER COMPRESSOR ASSEMBLY
a.
E127549
1.833,1 2.375,1 true 0.906,0.99 1.448,0.99 true 2.427,0.938 3.042,1.135 0.615,0.198 10 SSR+ 0.479,0.906 1.094,1.104 0.615,0.198 10 SSR-

Remove the cooler compressor assembly (A/C lock sensor).

Click hereVehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SSR+) - 2 (SSR-) 20°C (68°F) 160 to 320 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COOLER COMPRESSOR ASSEMBLY)

NG

REPLACE COOLER COMPRESSOR ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COOLER COMPRESSOR ASSEMBLY)
a.

Disconnect the G80 air conditioning amplifier assembly connector.


b.

Disconnect the B68 cooler compressor assembly (A/C lock sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G80-21 (LOCK) - B68-1 (SSR+) Always Below 1 Ω
G80-5 (SG-2) - B68-2 (SSR-) Always Below 1 Ω
G80-21 (LOCK) - Body ground Always 10 kΩ or higher
G80-5 (SG-2) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to Problem Symptoms Table) B
NG C



A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR