Home › Brake › BRAKE (REAR) › REAR BRAKE
RM30B0U _54 Brake _010845 BRAKE (REAR) _0057932 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 1.INSTALL REAR DISC

a.
C129072
2.754,0.13 2.905,0.291 0.151,0.161 10 *a 1.747,1.056 2.357,0.218 false 1.772,1.202 2.357,0.218 2.357,0.218 2.731,0.218 false
*a Matchmarks


Align the matchmarks of the rear disc and axle hub and install the rear disc.

HINT:

When replacing the disc with a new one, select the installation position where the disc has the smallest runout.



Hide 2.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 3.CHECK DISC RUNOUT

Hide 4.ADJUST PARKING BRAKE SHOE CLEARANCE

a.

Temporarily install the hub nuts.


b.
C266006
1.354,0.385 1.438,0.594 0.083,0.208 10 false .
V100135

Shoe Adjuster Contracts
V100136

Shoe Adjuster Expands


Remove the shoe adjusting hole plug, and then turn the adjuster to expand the shoe adjuster until the disc locks.


c.

Turn the shoe adjuster so that it contracts to a point where the disc rotates smoothly.

Standard:

8 notches



d.

Check that the shoe has no brake drag.


Hide 5.INSTALL REAR DISC BRAKE BUSH DUST BOOT

a.
C193400
0.752,4.147 0.921,4.306 0.169,0.159 10 *1
*1 Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to the entire circumference of a new rear disc brake bush dust boot where it contacts the rear disc brake cylinder mounting, and the entire inner circumference of both of its ends.

HINT:

Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to the rear disc brake bush dust boot.


NOTICE:

Apply a sufficient amount of lithium soap base glycol grease to the entire circumference of the rear disc brake bush dust boot and rear disc brake cylinder mounting contact surfaces.



b.

Install the 2 rear disc brake bush dust boots to the rear disc brake cylinder mounting.


Hide 6.INSTALL REAR DISC BRAKE CYLINDER SLIDE BUSH

a.
C187987
0.72,1.695 0.899,1.845 0.179,0.149 10 *1
*1 Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to a new rear disc brake rear cylinder slide pin where it contacts the rear disc brake cylinder slide bush.


b.

Install the rear disc brake cylinder slide bush to the rear disc brake rear cylinder slide pin.


Hide 7.INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C217115
0.743,2.915 0.938,3.064 0.196,0.149 10 *3 1.922,0.128 2.094,0.282 0.172,0.154 10 *1 0.53,2.289 0.702,2.459 0.172,0.17 10 *2 1.134,1.906 0.624,1.906 0.624,1.906 0.624,2.274 false 1.459,0.57 1.459,0.215 1.459,0.215 1.91,0.215 false
*1 Rear No. 1 Disc Brake Cylinder Slide Pin
*2 Rear Disc Brake Rear Cylinder Slide Pin
*3 Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to the sliding part and the seal surface of the 2 rear disc brake cylinder slide pins.


b.

Install the rear No. 1 disc brake cylinder slide pin and rear disc brake rear cylinder slide pin to the rear disc brake cylinder mounting.


Hide 8.INSTALL REAR DISC BRAKE CYLINDER MOUNTING LH

a.

Install the rear disc brake cylinder mounting with the 2 bolts.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)


Hide 9.INSTALL DISC BRAKE PAD SUPPORT PLATE

a.

Install the 2 pad support plates to the disc brake cylinder mounting.


Hide 10.INSTALL PAD WEAR INDICATOR PLATE

a.

Install the 2 indicator plates to the lower side of each pad.


Hide 11.INSTALL REAR ANTI-SQUEAL SHIM KIT

a.
C265927
1.554,0.66 1.724,0.809 0.170,0.149 10 *1 0.242,1.689 0.412,1.838 0.170,0.149 10 *2 1.677,2.581 1.846,2.730 0.170,0.149 10 *1 2.563,0.751 2.733,0.900 0.170,0.149 10 *2 0.338,1.19 0.338,1.674 false 0.987,1.058 1.335,0.733 1.335,0.733 1.535,0.733 false 2.394,2.287 2.117,2.665 2.117,2.665 1.885,2.665 false 3.087,2.201 3.087,0.832 3.087,0.832 2.772,0.832 false
*1 No. 1 anti-squeal shim
*2 No. 2 anti-squeal shim


Install the No. 1 and No. 2 anti-squeal shims to the rear disc brake pads.

NOTICE:
·

When replacing a worn pad, the shims must be replaced together with the pads.

·

Install the shims in the correct positions and direction as shown in the illustration.




Hide 12.INSTALL REAR DISC BRAKE PAD

a.

Install the 2 disc brake pads to the rear disc brake cylinder mounting.

NOTICE:

Make sure there is no oil or grease on the friction surface of the pads and disc.



Hide 13.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY LH

a.
C265925
0.771,2.354 0.552,2.125 0.552,2.125 0.396,2.125 false 1.396,2.604 1.865,2.813 1.865,2.813 2.073,2.813 false 0.198,2.042 0.344,2.188 0.146,0.146 10 *a 2.104,2.719 2.271,2.885 0.167,0.167 10 *b
*a Hold
*b Turn


Hold the rear disc brake cylinder slide pins and install the rear disc brake cylinder assembly to the disc brake cylinder mounting with the 2 bolts.

Torque:
26.5 N*m (270 kgf*cm, 20 ft.*lbf)


Hide 14.CONNECT REAR FLEXIBLE HOSE LH

a.

Install a new gasket and connect the flexible hose with a new union bolt.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)

HINT:

Install the flexible hose lock securely in the lock hole in the cylinder.



Hide 15.FILL RESERVOIR WITH BRAKE FLUID

Hide 16.REMOVE COWL TOP VENTILATOR LOUVER BRACKET LH

Hide 17.BLEED BRAKE LINE

Hide 18.INSTALL COWL TOP VENTILATOR LOUVER BRACKET LH

Hide 19.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)