Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM(for Start Function)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0057944 SMART KEY SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART KEY SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG)  


DESCRIPTION

If the engine switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) but does change to on (ACC)
Power Source Control:
·

Power Supply Condition

·

IG1 Relay Monitor(Inside)

·

IG2 Relay Monitor(Inside)

·

IG1 Relay Monitor(Outside)

·

IG2 Relay Monitor(Outside)

·

IG1 Circuit

·

IG2 Circuit


-


CAUTION / NOTICE / HINT

NOTICE:
·

When using the Techstream with the engine switch off to troubleshoot:

Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.

·

The smart key system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart key system (for Start Function) after confirming that the communication systems are functioning properly.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Start Function)>DIAGNOSTIC TROUBLE CODE CHART

·

If the smart key system is disabled through the customize function, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart key system (for Start Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Start Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After completing repairs, confirm that the problem does not occur.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG2 RELAY)
a.

Disconnect the G82 connectors from the certification ECU (smart key ECU assembly).


b.

Remove the IG2 relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-9 (IG2D) - 1 Always Below 1 Ω
2 - Body ground
G82-9 (IG2D) or 1 - Body ground 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT IG2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT IG2 RELAY
a.
C279145
2.031,0.625 1.677,0.385 false 2.604,0.677 2.917,0.469 false 2.385,1.135 2.875,1.135 false 2.448,1.635 2.906,1.635 false 0.24,0.667 0.396,0.865 0.156,0.198 10 5 1.188,0.677 1.344,0.875 0.156,0.198 10 3 0.24,1.198 0.396,1.396 0.156,0.198 10 1 1.188,1.219 1.375,1.417 0.188,0.198 10 2 1.552,0.26 1.708,0.458 0.156,0.198 10 1 2.969,0.344 3.125,0.542 0.156,0.198 10 2 2.979,1.073 3.135,1.271 0.156,0.198 10 5 3,1.563 3.156,1.76 0.156,0.198 10 3

Remove the IG2 relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE IG2 RELAY

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the G84 connector from the certification ECU (smart key ECU assembly).


b.

Disconnect the 3C and 3D connectors from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-6 (IG1D) - 3C-43 Always Below 1 Ω
3D-9 - Body ground
G84-6 (IG1D) or 3C-43 - Body ground 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

C278638
3.365,2.229 3.854,2.5 0.49,0.271 1.531,0.385 2.021,0.656 0.49,0.271 4.542,0.406 5.031,0.677 0.49,0.271 0.365,0.198 0.677,0.354 0.313,0.156 10 false *a 1.698,0.438 2.021,0.604 0.323,0.167 10 false 3C 4.708,0.469 5.031,0.635 0.323,0.167 10 false 3D 3.5,2.292 3.823,2.458 0.323,0.167 10 false 3A
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3A-1 - 3C-27 Battery voltage not applied to terminals 3D-9 and 3C-43 10 kΩ or higher
Battery voltage applied to terminals 3D-9 and 3C-43 Below 1 Ω
3A-1 - 3C-1 Battery voltage not applied to terminals 3D-9 and 3C-43 10 kΩ or higher
Battery voltage applied to terminals 3D-9 and 3C-43 Below 1 Ω
3A-1 - 3C-3 Battery voltage not applied to terminals 3D-9 and 3C-43 10 kΩ or higher
Battery voltage applied to terminals 3D-9 and 3C-43 Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage according to the value(s) in the table below.

B264896
1.979,0.854 2.5,1.104 0.521,0.25 4.615,0.865 5.135,1.115 0.521,0.25 2,1.74 2.167,2.354 false 4.354,1.635 4.135,2.302 false 0.542,0.271 0.854,0.469 0.313,0.198 10 *a 2.083,0.896 2.521,1.073 0.438,0.177 10 G82 4.75,0.927 5.188,1.104 0.438,0.177 10 G84 3.969,2.354 4.406,2.531 0.438,0.177 10 IG1D 2.031,2.396 2.469,2.573 0.438,0.177 10 IG2D
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Voltage:
Tester Connection Switch Condition Specified Condition
G82-9 (IG2D) - Body ground Engine switch on (ACC) → Engine switch on (IG) 1 V or less → 9 V or higher
G84-6 (IG1D) - Body ground Engine switch on (ACC) → Engine switch on (IG) 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)