The rear airbag sensor LH or RH consists of a lateral deceleration sensor, etc.
If the airbag sensor assembly receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.
DTC B1630/23, B1632/81, B1635/24 or B1637/82 is stored when a malfunction is detected in the rear airbag sensor LH or RH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1630/23 | Rear Airbag Sensor RH Circuit Malfunction | Either condition is met:
·
A rear airbag sensor RH malfunction. ·
An airbag sensor assembly malfunction. |
·
Rear airbag sensor RH ·
Airbag sensor assembly |
| B1632/81 | Lost Communication with Rear Airbag Sensor RH | Either condition is met:
·
A rear airbag sensor RH malfunction. ·
An airbag sensor assembly malfunction. |
·
Rear airbag sensor RH ·
Airbag sensor assembly |
| B1635/24 | Rear Airbag Sensor LH Circuit Malfunction | Either condition is met:
·
A rear airbag sensor LH malfunction. ·
An airbag sensor assembly malfunction. |
·
Rear airbag sensor LH ·
Airbag sensor assembly |
| B1637/82 | Lost Communication with Rear Airbag Sensor LH | Either condition is met:
·
A rear airbag sensor LH malfunction. ·
An airbag sensor assembly malfunction. |
·
Rear airbag sensor LH ·
Airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After replacing the airbag sensor assembly, refer to initialization.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Turn the ignition switch to ON.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1635/24 or B1637/82 is output |
| DTC B1630/23 or B1632/81 is output |
| DTC B1630/23, B1632/81, B1635/24 and B1637/82 are not output |
Codes other than DTC B1630/23, B1632/81, B1635/24 and B1637/82 may be output at this time, but they are not related to this check.
DTC B1635/24 or B1637/82 is output
DTC B1630/23 or B1632/81 is output
DTC B1630/23, B1632/81, B1635/24 and B1637/82 are not output
| *1 | Rear Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the rear airbag sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1630/23 or B1632/81 is output |
| DTC B1635/24 or B1637/82 is output |
| DTC B1630/23, B1632/81, B1635/24 and B1637/82 are not output |
Codes other than DTC B1630/23, B1632/81, B1635/24 and B1637/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the rear airbag sensor RH and LH to their original positions and connect the connectors to them.
DTC B1630/23 or B1632/81 is output
DTC B1635/24 or B1637/82 is output
DTC B1630/23, B1632/81, B1635/24 and B1637/82 are not output
| *1 | Rear Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the rear airbag sensor RH with LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1635/24 or B1637/82 is output |
| DTC B1630/23 or B1632/81 is output |
| DTC B1630/23, B1632/81, B1635/24 and B1637/82 are not output |
Codes other than DTC B1630/23, B1632/81, B1635/24 and B1637/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.
DTC B1635/24 or B1637/82 is output
DTC B1630/23 or B1632/81 is output
DTC B1630/23, B1632/81, B1635/24 and B1637/82 are not output