The 4WD ECU assembly determines that the vehicle is turning based on the signals sent from the steering angle sensor (spiral with sensor cable sub-assembly).
The steering angle sensor signal is sent to the 4WD ECU assembly via the CAN communication system.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1297/97 | Steering Angle Sensor | When voltage of 4WD ECU assembly IG terminal is 9.5 V or more, and steering angle sensor (spiral with sensor cable sub-assembly) malfunction signal is received. | ·
ECU-B NO. 1 fuse ·
Steering angle sensor (Spiral with sensor cable sub-assembly) ·
CAN communication system ·
4WD ECU assembly ·
Wire harness and connector |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check the condition of each related circuit connector before troubleshooting.
Clear the DTC.
Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON again and check that no CAN communication system DTC(s) is output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Start the engine.
Drive the vehicle at a speed of 35 km/h (24 mph), turn the steering wheel to the right and left and check that no brake control system (steering angle sensor) DTC (C1432, C1433 or C1434) is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Neither CAN communication system DTC nor brake control system DTC is output | A |
| CAN communication system DTC is output | B |
| Brake control system (steering angle sensor) DTC (C1432, C1433 or C1434) is output | C |
When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system before repairing each corresponding sensor.
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
C
| *a | Front view of wire harness connector
(to Steering Angle Sensor [Spiral with Sensor Cable Sub-assembly]) |
Remove the steering wheel and the column cover lower.
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>REMOVAL
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the steering angle sensor (spiral with sensor cable sub-assembly) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G12-4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| G12-5 (BAT) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Steering Angle Sensor [Spiral with Sensor Cable Sub-assembly]) |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G12-1 (ESS) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Chassis / Four Wheel Drive / Data List.
Read the value displayed on the Techstream.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Steering Angle Value | Steering angle value | Min.: -3276.8°
Max.: 3276.7° |
Left turn: Increase
Right turn: Decrease |
Changes in proportion with the amount of steering wheel rotation during steering operation. |
| Tester Display |
|---|
| Steering Angle Value |
The steering angle sensor value changes in accordance with the steering wheel movement.
| Proceed to |
|---|
| OK |
| NG |
OK
NG