Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM30B0U _58 Vehicle Interior _010074 SUPPLEMENTAL RESTRAINT SYSTEMS _0058017 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1810/53  Short in Driver Side Squib 2nd Step Circuit  B1811/53  Open in Driver Side Squib 2nd Step Circuit  B1812/53  Short to GND in Driver Side Squib 2nd Step Circuit  B1813/53  Short to B+ in Driver Side Squib 2nd Step Circuit  


DESCRIPTION

The driver side squib 2nd step circuit consists of the airbag sensor assembly, spiral with sensor cable sub-assembly and horn button assembly.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side squib 2nd step circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1810/53 Short in Driver Side Squib 2nd Step Circuit
One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal 5 times in the driver side squib 2nd step circuit during the primary check.

·

A driver side squib 2nd step malfunction.

·

A spiral with sensor cable sub-assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

Spiral with sensor cable sub-assembly

·

Horn button assembly (Driver side squib 2nd step)

·

Airbag sensor assembly


B1811/53 Open in Driver Side Squib 2nd Step Circuit
One of the following conditions is met:
·

The airbag sensor assembly detects an open circuit signal in the driver side squib 2nd step circuit for 2 seconds.

·

A driver side squib 2nd step malfunction.

·

A spiral with sensor cable sub-assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

Spiral with sensor cable sub-assembly

·

Horn button assembly (Driver side squib 2nd step)

·

Airbag sensor assembly


B1812/53 Short to GND in Driver Side Squib 2nd Step Circuit
One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to ground signal in the driver side 2nd step circuit for 0.5 seconds.

·

A driver side squib 2nd step malfunction.

·

A spiral with sensor cable sub-assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

Spiral with sensor cable sub-assembly

·

Horn button assembly (Driver side squib 2nd step)

·

Airbag sensor assembly


B1813/53 Short to B+ in Driver Side Squib 2nd Step Circuit
One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to B+ signal in the driver side squib 2nd step circuit for 0.5 seconds.

·

A driver side squib 2nd step malfunction.

·

A spiral with sensor cable sub-assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

Spiral with sensor cable sub-assembly

·

Horn button assembly (Driver side squib 2nd step)

·

Airbag sensor assembly



WIRING DIAGRAM

C253303
4.729,1.823 5.052,1.979 0.323,0.156 10 false D2+ 4.729,2.667 4.979,2.823 0.25,0.156 10 false D2- 2.833,1.76 3.156,1.917 0.323,0.156 10 false D2+ 2.833,2.604 3.083,2.76 0.25,0.156 10 false D2- 2.073,1.76 2.396,1.917 0.323,0.156 10 false D2+ 2.073,2.604 2.323,2.76 0.25,0.156 10 false D2- 3.156,1.729 3.385,1.917 0.229,0.188 10 false 4 3.156,2.583 3.333,2.771 0.177,0.188 10 false 3 2.438,3.219 2.792,3.385 0.354,0.167 10 false G9 0.344,3.208 0.698,3.375 0.354,0.167 10 false z3 2.448,3.375 4,3.719 1.552,0.344 10 false Spiral with Sensor Cable Sub-assembly 0.344,3.396 2.198,3.792 1.854,0.396 10 false Horn Button Assembly (Driver Side Squib 2nd Step) 4.51,1.719 4.677,1.958 0.167,0.24 10 false 8 4.51,2.552 4.75,2.781 0.24,0.229 10 false 7 4.729,4.323 5.042,4.49 0.313,0.167 10 false G92 4.729,4.49 7.042,4.656 2.313,0.167 10 false Airbag Sensor Assembly 2.396,2.594 2.625,2.781 0.229,0.188 10 false 1 2.396,1.74 2.573,1.927 0.177,0.188 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

When installing the spiral with sensor cable sub-assembly and steering wheel, be sure to adjust the spiral with sensor cable sub-assembly as it may break if the steering wheel is turned before adjusting the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:

To perform the simulation method, enter check mode (signal check) with the Techstream (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK HORN BUTTON ASSEMBLY (DRIVER SIDE SQUIB 2ND STEP)
a.
C213939
0.479,2.052 0.906,2.365 0.427,0.313 2.073,2.271 2.448,2.49 false 1.854,2.729 2.229,3.094 false 0.125,0.469 0.313,0.646 0.188,0.177 10 false *1 0.792,1.188 0.969,1.365 0.177,0.177 10 false *2 1.573,1.51 1.76,1.688 0.188,0.177 10 false *a 2.188,1.25 2.365,1.427 0.177,0.177 10 false *3 2.49,2.438 2.667,2.615 0.177,0.177 10 false *5 2.26,3.021 2.448,3.198 0.188,0.177 10 false *b 2.635,1.979 2.813,2.156 0.177,0.177 10 false *4 2.344,0.625 2.469,0.802 0.125,0.177 10 false A 1.792,0.885 1.917,1.063 0.125,0.177 10 false C 1.667,0.885 1.792,1.063 0.125,0.177 10 false D 0.521,0.885 0.646,1.063 0.125,0.177 10 false E 0.281,0.885 0.406,1.063 0.125,0.177 10 false F 0.563,2.125 0.813,2.281 0.25,0.156 10 false z3
*1 Driver Side Squib 2nd Step
*2 Spiral with Sensor Cable Sub-assembly
*3 Airbag Sensor Assembly
*4 Connector E
*5 SST
*a Front view of wire harness connector
(to Driver Side Squib 2nd Step)
*b Color: Black


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the horn button assembly.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (black connector).

CAUTION:

Never connect the tester to the horn button assembly (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1810/53, B1811/53, B1812/53 or B1813/53 is not output
DTC B1810/53, B1811/53, B1812/53 or B1813/53 is output


HINT:

Codes other than DTC B1810/53, B1811/53, B1812/53 and B1813/53 may be output at this time, but they are not related to this check.



k.

Turn the ignition switch off.


l.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


m.

Disconnect SST from connector E.



DTC B1810/53, B1811/53, B1812/53 or B1813/53 is not output

DTC B1810/53, B1811/53, B1812/53 or B1813/53 is output

2.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly.


b.
C208247
0.188,0.781 0.5,0.938 0.313,0.156 10 false *1 1.135,1.521 1.448,1.677 0.313,0.156 10 false *2 2.677,1.646 2.99,1.802 0.313,0.156 10 false *3 2.469,1.01 2.719,1.198 0.25,0.188 10 false A 2.083,1.281 2.354,1.469 0.271,0.188 10 false B 1.771,1.271 2.042,1.458 0.271,0.188 10 false C 1.615,1.271 1.885,1.458 0.271,0.188 10 false D 0.615,1.271 0.885,1.458 0.271,0.188 10 false E 0.417,1.271 0.688,1.458 0.271,0.188 10 false F
*1 Driver Side Squib 2nd Step
*2 Spiral with Sensor Cable Sub-assembly
*3 Airbag Sensor Assembly


Check that the connectors (on the airbag sensor assembly side and horn button assembly side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR OR SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT
a.
C213940
0.688,1.906 1.094,2.198 0.406,0.292 1.854,2.729 2.229,3.094 false 1.625,2.125 1.167,2.604 true 1.74,2.125 2.167,2.604 true 0.115,0.469 0.448,0.844 0.333,0.375 10 false *1 1.031,1.208 1.208,1.385 0.177,0.177 10 false *2 1.573,1.51 1.76,1.688 0.188,0.177 10 false *a 2.677,1.26 2.854,1.438 0.177,0.177 10 false *3 2.26,3.021 2.448,3.198 0.188,0.177 10 false *b 2.083,1.938 2.26,2.115 0.177,0.177 10 false *4 2.552,0.625 2.677,0.802 0.125,0.177 10 false A 1.813,0.906 2.063,1.281 0.25,0.375 10 false C 2.188,0.917 2.448,1.208 0.26,0.292 10 false B 1.688,0.906 1.958,1.281 0.271,0.375 10 false D 0.542,0.917 0.75,1.323 0.208,0.406 10 false E 0.323,0.917 0.656,1.365 0.333,0.448 10 false F 0.948,2.573 1.344,2.813 0.396,0.24 10 false D2- 2.219,2.604 2.573,2.927 0.354,0.323 10 false D2+ 0.771,1.969 1.365,2.375 0.594,0.406 10 false z3
*1 Driver Side Squib 2nd Step
*2 Spiral with Sensor Cable Sub-assembly
*3 Airbag Sensor Assembly
*4 Connector E
*a Front view of wire harness connector
(to Driver Side Squib 2nd Step)
*b Color: Black


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z3-2 (D2+) - Body ground Ignition switch ON Below 1 V
z3-1 (D2-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-2 (D2+) - z3-1 (D2-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-2 (D2+) - z3-1 (D2-) Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-2 (D2+) - Body ground Always 1 MΩ or higher
z3-1 (D2-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK AIRBAG SENSOR ASSEMBLY

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK AIRBAG SENSOR ASSEMBLY
a.
C146255
0.229,0.604 0.542,0.76 0.313,0.156 10 false *1 1.094,1.281 1.406,1.438 0.313,0.156 10 false *2 2.594,1.375 2.906,1.531 0.313,0.156 10 false *3 1.781,1.031 2.094,1.188 0.313,0.156 10 false C 1.646,1.031 1.979,1.188 0.333,0.156 10 false D 0.552,1.031 0.885,1.188 0.333,0.156 10 false E 0.406,1.031 0.74,1.188 0.333,0.156 10 false F 2.344,0.781 2.656,0.938 0.313,0.156 10 false A
*1 Driver Side Squib 2nd Step
*2 Spiral with Sensor Cable Sub-assembly
*3 Airbag Sensor Assembly


Connect the connectors to the horn button assembly and airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1810/53, B1811/53, B1812/53 or B1813/53 is not output
DTC B1810/53, B1811/53, B1812/53 or B1813/53 is output


HINT:

Codes other than DTC B1810/53, B1811/53, B1812/53 and B1813/53 may be output at this time, but they are not related to this check.




DTC B1810/53, B1811/53, B1812/53 or B1813/53 is not output

DTC B1810/53, B1811/53, B1812/53 or B1813/53 is output

5.CHECK INSTRUMENT PANEL WIRE
a.
C213941
0.365,2.198 0.76,2.469 0.396,0.271 1.448,2.417 1.24,2.875 true 1.604,2.417 2.313,2.875 true 1.792,0.438 1.979,0.615 0.188,0.177 10 false *1 0.958,1.156 1.135,1.333 0.177,0.177 10 false *2 1.573,1.542 1.76,1.719 0.188,0.177 10 false *a 2.531,1.25 2.708,1.427 0.177,0.177 10 false *3 2.292,1.938 2.469,2.115 0.177,0.177 10 false *4 0.448,2.25 0.719,2.417 0.271,0.167 10 false G9 2.354,0.656 2.479,0.833 0.125,0.177 10 false A 1.667,0.917 1.792,1.094 0.125,0.177 10 false C 1.99,0.917 2.115,1.094 0.125,0.177 10 false B 1.479,0.917 1.604,1.094 0.125,0.177 10 false D 0.438,0.917 0.563,1.094 0.125,0.177 10 false E 0.25,0.917 0.375,1.094 0.125,0.177 10 false F 1.031,2.917 1.542,3.146 0.51,0.229 10 false 4 (D2+) 2.24,2.906 2.833,3.104 0.594,0.198 10 false 3 (D2-)
*1 Instrument Panel Wire
*2 Spiral with Sensor Cable Sub-assembly
*3 Airbag Sensor Assembly
*4 Connector C
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly)


Disconnect the instrument panel wire connector from the spiral with sensor cable sub-assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-4 (D2+) - Body ground Ignition switch ON Below 1 V
G9-3 (D2-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-4 (D2+) - G9-3 (D2-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-4 (D2+) - G9-3 (D2-) Always 1 MΩ or higher



j.

Restore the released activation prevention mechanism of connector B to its original condition.


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-4 (D2+) - Body ground Always 1 MΩ or higher
G9-3 (D2-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE