Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM30B0U _58 Vehicle Interior _010074 SUPPLEMENTAL RESTRAINT SYSTEMS _0058017 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1875/67  Short in Passenger Side Front Seat Cushion Squib Circuit  B1876/67  Open in Passenger Side Front Seat Cushion Squib Circuit  B1877/67  Short to GND in Passenger Side Front Seat Cushion Squib Circuit  B1878/67  Short to B+ in Passenger Side Front Seat Cushion Squib Circuit  


DESCRIPTION

The front seat cushion squib RH circuit consists of the airbag sensor assembly and the front seat airbag sub-assembly.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the front seat cushion squib RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1875/67 Short in Passenger Side Front Seat Cushion Squib Circuit
One of the following conditions is met:
·

The airbag sensor assembly receives a line short circuit signal 5 times in the front seat cushion squib RH circuit during primary check.

·

A front seat cushion squib RH malfunction

·

An airbag sensor assembly malfunction


·

Floor wire

·

Front seat airbag sub-assembly (Front seat cushion squib RH)

·

Airbag sensor assembly


B1876/67 Open in Passenger Side Front Seat Cushion Squib Circuit
One of the following conditions is met:
·

The airbag sensor assembly receives an open circuit signal in the front seat cushion squib RH circuit for 2 seconds.

·

A front seat cushion squib RH malfunction

·

An airbag sensor assembly malfunction


·

Floor wire

·

Front seat airbag sub-assembly (Front seat cushion squib RH)

·

Airbag sensor assembly


B1877/67 Short to GND in Passenger Side Front Seat Cushion Squib Circuit
One of the following conditions is met:
·

The airbag sensor assembly receives a short circuit to ground signal in the front seat cushion squib RH circuit for 0.5 seconds.

·

A front seat cushion squib RH malfunction

·

An airbag sensor assembly malfunction


·

Floor wire

·

Front seat airbag sub-assembly (Front seat cushion squib RH)

·

Airbag sensor assembly


B1878/67 Short to B+ in Passenger Side Front Seat Cushion Squib Circuit
One of the following conditions is met:
·

The airbag sensor assembly receives a short circuit to B+ signal in the front seat cushion squib RH circuit for 0.5 seconds.

·

A front seat cushion squib RH malfunction

·

An airbag sensor assembly malfunction


·

Floor wire

·

Front seat airbag sub-assembly (Front seat cushion squib RH)

·

Airbag sensor assembly



WIRING DIAGRAM

C253326
1.979,1.552 2.438,1.75 0.458,0.198 10 false FCP+ 2.458,2.406 2.917,2.604 0.458,0.198 10 false 1 2.01,2.417 2.469,2.615 0.458,0.198 10 false FCP- 2.458,1.563 2.917,1.76 0.458,0.198 10 false 2 0.75,3.052 1.208,3.25 0.458,0.198 10 false M15 0.75,3.229 2.75,3.604 2,0.375 10 false Front Seat Airbag Sub-assembly (Front Seat Cushion Squib RH) 4.792,1.677 5.25,1.875 0.458,0.198 10 false FCP+ 4.521,1.563 4.74,1.76 0.219,0.198 10 false 13 4.51,2.406 4.74,2.625 0.229,0.219 10 false 14 4.781,2.521 5.24,2.719 0.458,0.198 10 false FCP- 4.792,4.167 5.25,4.365 0.458,0.198 10 false M25 4.802,4.333 6.458,4.51 1.656,0.177 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:

To perform the simulation method, enter check mode (signal check) with the Techstream (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).


PROCEDURE

1.CHECK FRONT SEAT AIRBAG SUB-ASSEMBLY RH (FRONT SEAT CUSHION SQUIB RH)
a.
E272064
0.198,2 0.615,2.229 0.417,0.229 1.75,2.927 1.958,3.104 false 2.01,2.823 2.219,3 false 1.021,0.052 1.333,0.208 0.313,0.156 10 false *1 2.219,1.188 2.531,1.344 0.313,0.156 10 false *2 2.365,1.969 2.677,2.125 0.313,0.156 10 false *3 2.26,2.979 2.573,3.135 0.313,0.156 10 false *4 1.5,1.458 1.813,1.615 0.313,0.156 10 false *a 1.969,3.167 2.281,3.323 0.313,0.156 10 false *b 0.26,2.042 0.688,2.26 0.427,0.219 10 false M15 2,0.229 2.313,0.385 0.313,0.156 10 false A 1.469,0.5 1.792,0.729 0.323,0.229 10 false C 1.25,0.5 1.573,0.729 0.323,0.229 10 false D
*1 Front Seat Cushion Squib RH
*2 Airbag Sensor Assembly
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Front Seat Cushion Squib RH)
*b Color: Red


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the front seat airbag sub-assembly connectors.


d.

Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat airbag sub-assembly (front seat cushion squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1875/67, B1876/67, B1877/67 or B1878/67 is not output.


HINT:

Codes other than DTC B1875/67, B1876/67, B1877/67 or B1878/67 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly.


b.
C208249
0.852,0.944 1.045,1.183 0.193,0.24 10 D 0.647,0.456 0.84,0.624 0.193,0.168 10 *1 1.252,0.448 1.446,0.615 0.193,0.168 10 *2 1.698,1.671 1.892,1.838 0.193,0.168 10 *3 1.084,0.944 1.296,1.165 0.212,0.221 10 C 1.497,0.944 1.709,1.174 0.212,0.23 10 B 1.902,0.651 2.095,0.835 0.193,0.184 10 A
*1 Front Seat Cushion Squib RH
*2 Floor Wire
*3 Airbag Sensor Assembly


Check that the connectors (on the airbag sensor assembly side and front seat airbag sub-assembly side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not damaged or deformed.



Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE
a.

Disconnect the connectors from the airbag sensor assembly.


b.
E272065
0.26,2.438 0.646,2.708 0.385,0.271 0.885,3.063 1.344,2.823 false 2.063,3.052 1.656,2.833 false 1.104,0.302 1.417,0.458 0.313,0.156 10 false *1 2.271,1.417 2.583,1.573 0.313,0.156 10 false *2 1.969,2.531 2.281,2.688 0.313,0.156 10 false *3 1.406,1.927 1.719,2.083 0.313,0.156 10 false *a 0.323,2.49 0.698,2.677 0.375,0.188 10 false M15 0.542,3.083 0.99,3.281 0.448,0.198 10 false FCP- 1.938,3.083 2.385,3.281 0.448,0.198 10 false FCP+ 2.083,0.49 2.396,0.646 0.313,0.156 10 false A 1.542,0.781 1.854,0.938 0.313,0.156 10 false C 1.333,0.781 1.646,0.938 0.313,0.156 10 false D
*1 Front Seat Cushion Squib RH
*2 Airbag Sensor Assembly
*3 Connector C
*a Front view of wire harness connector
(to Front Seat Cushion Squib RH)


Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M15-1 (FCP-) - Body ground Ignition switch ON Below 1 V
M15-2 (FCP+) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M15-1 (FCP-) - M15-2 (FCP+) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M15-1 (FCP-) - M15-2 (FCP+) Always 1 MΩ or higher



j.

Restore the released activation prevention mechanism of connector B to its original condition.


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M15-1 (FCP-) - Body ground Always 1 MΩ or higher
M15-2 (FCP+) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK AIRBAG SENSOR ASSEMBLY

NG

REPLACE FLOOR WIRE

4.CHECK AIRBAG SENSOR ASSEMBLY
a.
C146259
0.76,0.229 0.99,0.385 0.229,0.156 10 false *1 1.906,1.313 2.083,1.49 0.177,0.177 10 false *2 1.01,0.667 1.146,0.833 0.135,0.167 10 false D 1.135,0.656 1.271,0.823 0.135,0.167 10 false C 1.656,0.427 1.885,0.583 0.229,0.156 10 false A
*1 Front Seat Cushion Squib RH
*2 Airbag Sensor Assembly


Connect the connectors to the front seat airbag sub-assembly and the airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1875/67, B1876/67, B1877/67 or B1878/67 is not output.


HINT:

Codes other than DTC B1875/67, B1876/67, B1877/67 or B1878/67 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG