Home › Vehicle Interior › SEAT › FRONT SEATBACK HEATER(for Front Passenger Side)
RM30B0U _58 Vehicle Interior _009409 SEAT _0058127 FRONT SEATBACK HEATER(for Front Passenger Side) A

SEAT  FRONT SEATBACK HEATER(for Front Passenger Side)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS


PROCEDURE

Hide 1.INSTALL FRONT SEATBACK HEATER ASSEMBLY RH

a.

Set the front seatback heater assembly RH on the separate type front seatback cover.


b.
B341138

Using a tacker, install the front seatback heater assembly RH to the separate type front seatback cover with 14 new tack pins as shown in the illustration.

NOTICE:

Do not substitute other metal parts for tack pins.



Hide 2.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

a.

Set the separate type front seatback cover in place.


b.
B342803
1.563,3.896 1.948,3.438 false 0.542,4 0.688,3.177 true 1.979,3.281 2.292,3.438 0.313,0.156 10 false *1 0.5,4.031 0.813,4.188 0.313,0.156 10 false *a
*1 Hog Ring Pliers
*a Cutout


Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 8 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



HINT:

Install the hog rings at the cutouts if they are there.



c.

Pass the separate type front seatback cover bracket through the separate type front seatback pad.


d.

Install the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


e.

Close the 2 fasteners.


f.
B340871

Pull the straps to tighten them and confirm that there is a protrusion visible on each side.


g.
B338257
1.635,3.74 2.052,3.323 false 0.438,3.813 0.646,3.094 true 2.052,3.188 2.365,3.344 0.313,0.156 10 *1 0.354,3.813 0.667,3.969 0.313,0.156 10 *a
*1 Hog Ring Pliers
*a Cutout


Using hog ring pliers, connect the straps of the separate type front seatback cover to the separate type front seatback frame sub-assembly RH with 3 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the straps of the separate type front seatback cover.



HINT:

Install the hog rings at the cutouts if they are there.



h.
B342804
1.573,3.854 1.99,3.438 false 0.438,3.865 0.688,3.167 true 2,3.292 2.313,3.448 0.313,0.156 10 false *1 0.354,3.875 0.667,4.031 0.313,0.156 10 false *a
*1 Hog Ring Pliers
*a Cutout


Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback frame sub-assembly RH with 5 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



HINT:

Install the hog rings at the cutouts if they are there.



Hide 3.INSTALL FRONT SEAT HEADREST SUPPORT

a.

Attach the 4 claws to install the 2 front seat headrest supports.


Hide 4.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY

a.
B342798

Install the separate type front seatback assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.
B342797

Attach the 2 hook.


c.

Connect the wire harness of the front seat inner belt assembly with the screw.


d.
B342795
1.427,0.885 0.76,0.875 false 0.594,0.792 0.906,0.948 0.313,0.156 10 false *1
*1 Fastener


Attach the fastener to connect the wire harness of the front seat side airbag.


e.
B342794
1.385,0.771 1.573,0.969 true 1.125,0.583 1.438,0.427 true 1.125,1.313 1.354,1.354 true 0.99,1.729 0.729,1.917 true 1.594,0.917 1.906,1.073 0.313,0.156 10 true *1 1.448,0.302 1.854,0.604 0.406,0.302 10 true *2 0.594,1.927 0.906,2.083 0.313,0.156 10 true *1 1.354,1.26 1.667,1.417 0.313,0.156 10 true *1
*1 Wire Harness Clamp
*2 Connector Clamp


Attach the 4 wire harness clamps and connector clamp to connect the wire harness of the front seat side airbag.


f.
B340392

Attach the wire harness clamp and connector clamp.


g.

Cconnect the connector.


h.

Connect the rubber band.


Hide 5.INSTALL FRONT INNER SEAT CUSHION SHIELD RH

a.
B339920
1.833,0.417 1.833,0.354 false
V100135

First
V100136

Second


Attach the 3 guides and 2 claws to install the front inner seat cushion shield RH as indicated by the arrows in the order shown in the illustration.


Hide 6.INSTALL FRONT SEAT CUSHION SHIELD RH

a.
B342805
2,1.958 2.021,2 false
V100135

First
V100136

Second


Attach the 3 guides and claw to install the front seat cushion shield RH as indicated by the arrows in the order shown in the illustration.


b.
B342791

Attach the claw and 2 clips.


Hide 7.INSTALL RECLINING ADJUSTER RELEASE HANDLE RH

a.

Attach the claw to install the reclining adjuster release handle RH.


Hide 8.INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the driver seat.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>INSTALLATION


Hide 9.INSPECT SEAT HEATER SYSTEM