Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM30B0U _58 Vehicle Interior _009874 DOOR LOCK _0058010 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Only Back Door cannot be Opened  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives signals from the back door opener switch assembly. Then, the main body ECU (multiplex network body ECU) activates the back door lock motor.

WIRING DIAGRAM

E271272
1.958,1.656 2.979,2.021 1.021,0.365 10 false Back Door Lock Assembly 1.958,1.51 2.448,1.708 0.49,0.198 10 false U12 2.021,1.281 2.51,1.479 0.49,0.198 10 false ACT- 2.635,1.292 3.125,1.49 0.49,0.198 10 false ACT+ 1.833,1.031 2.052,1.219 0.219,0.188 10 false 1 3.073,0.677 3.292,0.865 0.219,0.188 10 false 3 3.073,1.042 3.292,1.229 0.219,0.188 10 false 2 3.573,0.792 3.906,0.99 0.333,0.198 10 false 3E 3.583,1.729 3.917,1.927 0.333,0.198 10 false 3E 3.594,2.167 3.927,2.365 0.333,0.198 10 false 3D 2.802,0.719 3.073,0.927 0.271,0.208 10 false D+ 5.042,0.781 5.375,0.979 0.333,0.198 10 false A 3.583,0.604 3.802,0.792 0.219,0.188 10 false 33 3.625,1.542 3.844,1.729 0.219,0.188 10 false 8 3.625,1.979 3.844,2.167 0.219,0.188 10 false 9 4.51,1.281 5.24,1.49 0.729,0.208 10 false D/L BACK 3.958,0.969 4.417,1.396 0.458,0.427 10 false from Battery 5.052,3.063 5.385,3.26 0.333,0.198 10 false A 4.958,3.906 5.302,4.104 0.344,0.198 10 false G78 5.323,0.802 5.938,1.01 0.615,0.208 10 false BCTY 5.323,3.073 5.792,3.281 0.469,0.208 10 false TR+ 4.146,2.615 5.229,2.833 1.083,0.219 10 false D/L BACK Relay 5.01,0.604 5.229,0.792 0.219,0.188 10 false 20 5.063,2.875 5.281,3.063 0.219,0.188 10 false 6 5.021,3.719 5.25,3.906 0.229,0.188 10 false 23 5.052,5.833 5.271,6.021 0.219,0.188 10 false 27 5.323,3.917 5.938,4.125 0.615,0.208 10 false BDSU*1 5.313,5.938 5.927,6.146 0.615,0.208 10 false TSW5 1.469,6.24 1.813,6.438 0.344,0.198 10 false U7 1.688,5.833 1.906,6.021 0.219,0.188 10 false 2 1.667,3.802 1.885,3.99 0.219,0.188 10 false 2 3.125,3.802 3.344,4.01 0.219,0.208 10 false 3 3.125,5.833 3.344,6.042 0.219,0.208 10 false 3 2.833,5.833 3.104,6.031 0.271,0.198 10 false UL 2.865,3.813 3.135,4.01 0.271,0.198 10 false UL 1.865,3.802 2.083,3.99 0.219,0.188 10 false E 1.854,5.833 2.073,6.021 0.219,0.188 10 false E 1.458,6.406 4.052,6.656 2.594,0.25 10 false Back Door Opener Switch Assembly*2 1.438,4.219 1.781,4.417 0.344,0.198 10 false U7 1.427,4.385 4.021,4.635 2.594,0.25 10 false Back Door Opener Switch Assembly*1 0.74,7.521 2.667,7.75 1.927,0.229 10 false : CAN Communication Line 0.344,6.927 2.521,7.156 2.177,0.229 10 false *1: w/o Smart Key System 0.354,7.219 2.531,7.448 2.177,0.229 10 false *2: w/ Smart Key System 4.031,5.823 4.25,6.01 0.219,0.188 10 false *2 4.01,3.813 4.229,4 0.219,0.188 10 false *1 4.333,4.698 5.979,5.156 1.646,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 5.24,6.74 6.76,7.208 1.521,0.469 10 false Certification ECU (Smart Key ECU Assembly)*2 5.24,6.583 5.583,6.781 0.344,0.198 10 false G83 6.271,4.99 6.49,5.177 0.219,0.188 10 false *2 2.073,2.875 3.792,3.271 1.719,0.396 10 false Instrument Panel Junction Block Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

The power door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power door lock control system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

w/ Smart Key System:

Before performing this troubleshooting, perform troubleshooting for "Back Door Entry Unlock Function does not Operate" for the Smart Key system (for Entry Function) first.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>Back Door Entry Unlock Function does not Operate

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specification.


Result:
Proceed to
w/o Smart Key System
w/ Smart Key System



w/o Smart Key System

2.CHECK POWER DOOR LOCK OPERATION (BASIC FUNCTION)

w/ Smart Key System

8.INSPECT BACK DOOR LOCK ASSEMBLY
2.CHECK POWER DOOR LOCK OPERATION (BASIC FUNCTION)
a.

Check the power door lock basic functions.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

The power door lock basic functions operate properly.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING TECHSTREAM (Back Door Open)

NG

3.READ VALUE USING TECHSTREAM (Back Door Open)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Main Body / Data List / All Data.


e.

Read the Data List according to the display on the Techstream.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back Door Open Back door lock signal Permit or Prohibit Permit: Back door unlocked
Prohibit: Back door locked
-
Body Electrical > Main Body > Data List
Tester Display
Back Door Open
50003 123 27
OK:

The Techstream indicates Permit or Prohibit according to the door lock operation shown in the table.



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING TECHSTREAM (Trunk and Back-Door Open)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.PERFORM ACTIVE TEST USING TECHSTREAM (Trunk and Back-Door Open)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the Techstream.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Trunk and Back-Door Open Back door lock motor OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Trunk and Back-Door Open
50004 123 3
OK:

The back door lock assembly unlatches when ON is selected.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING TECHSTREAM (Back Door Open Handle SW)

NG

8.INSPECT BACK DOOR LOCK ASSEMBLY
5.READ VALUE USING TECHSTREAM (Back Door Open Handle SW)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Main Body / Data List / All Data.


e.

Read the Data List according to the display on the Techstream.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back Door Open Handle SW Back door opener switch signal ON or OFF ON: Back door opener switch pushed
OFF: Back door opener switch not pushed
-
Body Electrical > Main Body > Data List
Tester Display
Back Door Open Handle SW
50003 123 29
OK:

The Techstream indicates ON or OFF according to the switch operation shown in the table.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

6.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY
6.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY
a.

Remove the back door opener switch assembly.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>REMOVAL


b.

Inspect the back door opener switch assembly.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPLACE BACK DOOR OPENER SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the G78 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the U7 back door opener switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U7-3 (UL) - G78-23 (BDSU) Always Below 1 Ω
U7-2 (E) - Body ground
U7-3 (UL) or G78-23 (BDSU) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BACK DOOR LOCK ASSEMBLY
a.

Remove the back door lock assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL


b.

Inspect the back door lock assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
a.

Disconnect the 3E instrument panel junction block assembly connector.


b.

Disconnect the U12 back door lock assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U12-2 (ACT+) - 3E-8 (TR+) Always Below 1 Ω
U12-3 (D+) - 3E-33 (BCTY)
U12-1 (ACT-) - Body ground
U12-2 (ACT+) or 3E-8 (TR+) - Body ground Always 10 kΩ or higher
U12-3 (D+) or 3E-33 (BCTY) - Body ground



Result:
Proceed to
OK
NG



OK

10.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Replace the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CHECK BACK DOOR OPEN OPERATION
11.CHECK BACK DOOR OPEN OPERATION
a.

Check that the back door can be opened.

OK:

The back door can be opened.



Result:
Proceed to
OK
NG



OK

END (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)