Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Key System)
RM30B0U _58 Vehicle Interior _009874 DOOR LOCK _0058013 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Key System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Key System)  No Answer-Back  


DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning light and/or wireless door lock buzzer answer-back function(s) does not operate. In such cases, hazard warning light and wireless door lock buzzer signal outputs from the main body ECU (multiplex network body ECU) may be malfunctioning.

WIRING DIAGRAM

B343414
2.531,0.49 4.969,0.781 2.438,0.292 10 false Hazard Warning Signal Switch Signal 5.583,2.927 6.896,3.448 1.313,0.521 10 false Combination Meter Assembly 5.573,2.76 6.01,2.958 0.438,0.198 10 false G17 2.813,4.125 4.5,4.49 1.688,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 2.813,3.958 3.25,4.156 0.438,0.198 10 false A 3.771,2.948 4.208,3.146 0.438,0.198 10 false BZR 3.438,2.813 3.875,3.01 0.438,0.198 10 false 21 2.198,2.813 2.635,3.01 0.438,0.198 10 false 55 0.552,3.594 2.365,3.896 1.813,0.302 10 false Wireless Door Lock Buzzer 0.563,3.427 1,3.625 0.438,0.198 10 false A12 1.604,2.938 2.042,3.135 0.438,0.198 10 false B 0.865,2.938 1.302,3.135 0.438,0.198 10 false E 1.885,2.823 2.323,3.021 0.438,0.198 10 false 1 0.594,2.823 1.031,3.021 0.438,0.198 10 false 2 5.74,0.49 6.177,0.688 0.438,0.198 10 false HAZ 5.49,0.365 5.927,0.563 0.438,0.198 10 false 3 0.802,5.354 2.875,5.635 2.073,0.281 10 false : CAN Communication Line 2.729,5.25 5.625,5.51 2.896,0.26 10 false Instrument Panel Junction Block Assembly 2.719,5.104 3.156,5.302 0.438,0.198 10 false 3B

CAUTION / NOTICE / HINT

NOTICE:

The wireless door lock control system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Key System)>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.READ VALUE USING TECHSTREAM (ANSWER-BACK OPERATION)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Customize Setting / Wireless Door Lock.


e.

Select the setting by referring to the table below.

Wireless Door Lock
Tester Display Description Default Setting ECU
Hazard Answer Back When the doors are locked by wireless operation, the hazard warning lights flash once.
When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
ON 0:OFF,1:ON Main body ECU (Multiplex network body ECU)
Wireless Buzzer Resp Wireless door lock buzzer response ON 0:OFF,1:ON Main body ECU (Multiplex network body ECU)
Wireless Buzzer Vol Wireless door lock buzzer volume Level 5 0000:Level7,0001:Level6,0010:Level5,0011:Level4,0100:Level3,0101:Level2,0110:Level1,0111:Level0 Main body ECU (Multiplex network body ECU)
50006 1

Result:
Proceed to
Both items are ON and except Level 0
Either item is OFF or Level 0



Both items are ON and except Level 0

2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

Either item is OFF or Level 0

2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
a.

Check the wireless door lock control function using the door control transmitter assembly.


Result:
Proceed to
Wireless door lock/unlock operates normally.
Wireless door lock/unlock does not operate normally.



Wireless door lock/unlock operates normally.

3.READ VALUE USING TECHSTREAM (DOOR UNLOCK DETECTION SWITCH)

Wireless door lock/unlock does not operate normally.

3.READ VALUE USING TECHSTREAM (DOOR UNLOCK DETECTION SWITCH)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the Techstream.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Lock Pos Front door RH unlock detection switch signal LOCK or UNLOCK LOCK: Front door RH locked
UNLOCK: Front door RH unlocked
-
FL Door Lock Pos Front door LH unlock detection switch signal LOCK or UNLOCK LOCK: Front door LH locked
UNLOCK: Front door LH unlocked
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Lock Pos
FL Door Lock Pos
50003 123 196,198
OK:

The Techstream should display as shown in the table according to door lock operation.



Result:
Result Proceed to
OK A
NG B



A

4.CHECK WIRELESS ANSWER-BACK OPERATION

B

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

4.CHECK WIRELESS ANSWER-BACK OPERATION
a.

Check the wireless answer-back operation using the door control transmitter assembly.


Result:
Proceed to
Only wireless door lock buzzer answer-back does not occur.
Only hazard warning light answer-back does not occur.



Only wireless door lock buzzer answer-back does not occur.

5.PERFORM ACTIVE TEST USING TECHSTREAM (WIRELESS DOOR LOCK BUZZER)

Only hazard warning light answer-back does not occur.

10.CHECK HAZARD WARNING LIGHTS OPERATION
5.PERFORM ACTIVE TEST USING TECHSTREAM (WIRELESS DOOR LOCK BUZZER)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the Techstream.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wireless Buzzer Wireless door lock buzzer OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Wireless Buzzer
50004 123 12

Result:
Proceed to
Wireless door lock buzzer does not turn on/off.
Wireless door lock buzzer turns on/off.



Wireless door lock buzzer does not turn on/off.

6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

Wireless door lock buzzer turns on/off.

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the wireless door lock buzzer and instrument panel junction block assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A12-1 (B) - 3B-55 Always Below 1 Ω
A12-2 (E) - Body ground Always Below 1 Ω
A12-1 (B) or 3B-55 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B337496
2,1 2.417,1.25 0.417,0.25 5.417,0.667 5.833,0.917 0.417,0.25 2.198,2.271 2.615,2.271 2.615,2.271 2.615,1.688 false 5.542,0.719 5.854,0.917 0.313,0.198 10 3B 2.146,1.052 2.458,1.25 0.313,0.198 10 A 1.896,2.188 2.208,2.385 0.313,0.198 10 BZR


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-55 - A-21 (BZR) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.REPLACE WIRELESS DOOR LOCK BUZZER

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

8.REPLACE WIRELESS DOOR LOCK BUZZER
a.

Temporarily replace the wireless door lock buzzer with a new one.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK BUZZER>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK WIRELESS DOOR LOCK BUZZER OPERATION
9.CHECK WIRELESS DOOR LOCK BUZZER OPERATION
a.

Check the operation of the wireless answer-back function.

OK:

Wireless answer-back function operates normally.



Result:
Proceed to
OK
NG



OK

END (WIRELESS DOOR LOCK BUZZER WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

10.CHECK HAZARD WARNING LIGHTS OPERATION
a.

Check that the hazard warning light blinks when the hazard warning signal switch is pressed.

OK:

Hazard warning light signal is normally.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO LIGHTING SYSTEM (Proceed to Hazard Warning Switch Circuit)