Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Key System)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0059577 IMMOBILISER SYSTEM(w/ Smart Key System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Key System)  Security Indicator Light Does not Blink  


DESCRIPTION

The certification ECU (smart key ECU assembly) blinks the security indicator light when the immobiliser is set (engine switch off, or driver door is opened and closed with engine switch on [IG]).

WIRING DIAGRAM

E274255
0.396,1.833 0.854,2.031 0.458,0.198 10 false G43 0.417,2.01 1.927,2.531 1.51,0.521 10 false Security Indicator Light (Telltale Light Assembly) 1.344,1.396 1.656,1.594 0.313,0.198 10 false E 1.25,0.844 1.563,1.042 0.313,0.198 10 false LP 5.458,1.833 6.021,2.063 0.563,0.229 10 false G84 5.563,0.708 5.875,0.906 0.313,0.198 10 false 18 1.594,0.688 1.906,0.885 0.313,0.198 10 false 21 1.604,1.25 1.917,1.448 0.313,0.198 10 false 13 5.833,0.813 6.146,1.01 0.313,0.198 10 false IND 5.479,2.01 7,2.448 1.521,0.438 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to the registration.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>REGISTRATION

·

The immobiliser system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the immobiliser system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (IMMOBILISER INDICATOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Smart Key / Active Test.


e.

Perform the Active Test according to the display on the Techstream.

Body Electrical > Smart Key > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Immobiliser Indicator Security indicator light OFF or ON -
Body Electrical > Smart Key > Active Test
Tester Display
Immobiliser Indicator
50004 125 28
OK:

The security indicator light operates normally.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)
a.

Disconnect the G43 security indicator light (telltale light assembly) connector.


b.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-18 (IND) - G43-21 (LP) Always Below 1 Ω
G43-13 (E) - Body ground Always Below 1 Ω
G84-18 (IND) - Body ground Always 10 kΩ or higher
G43-21 (LP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Disconnect the G43 security indicator light (telltale light assembly) connector.


b.

Measure the voltage and check the pulse according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G43-21 (LP) - Body ground Engine switch off → engine switch on (IG) Pulse generation → Below 2 V



Result:
Proceed to
OK
NG



OK

REPLACE SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)