Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Key System)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0059577 IMMOBILISER SYSTEM(w/ Smart Key System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Key System)  B2799  Immobiliser Malfunction  


DESCRIPTION

When there are communication malfunctions between the ECM and certification ECU (smart key ECU assembly), or when the communication ID codes do not match, the ECM stores this DTC.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Immobiliser Malfunction
Either condition is met (1 trip detection logic*):
·

A malfunction in the communication or communication lines between the ECM and certification ECU (smart key ECU assembly).

·

A matching communication code cannot be verified during communication between the ECM and certification ECU (smart key ECU assembly).


·

Certification ECU (smart key ECU assembly)

·

ECM

·

Harness or connector


DTC output confirmation operation (Either condition is met):
·

Within 10 seconds of an engine start operation being performed (with the shift lever in P and the brake pedal depressed, the engine switch is pressed while the key is being carried). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

10 seconds after the engine switch is turned on (IG) after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the engine switch being turned on (IG), and DTCs are stored after 6 seconds).



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2799 -

WIRING DIAGRAM

B344498
5.063,2.021 6.583,2.385 1.521,0.365 10 false Certification ECU (Smart Key ECU Assembly) 5.063,1.854 5.521,2.052 0.458,0.198 10 false G82 5.458,0.927 5.917,1.125 0.458,0.198 10 false EFIO 5.479,1.385 5.938,1.583 0.458,0.198 10 false EFII 1.469,0.927 1.844,1.125 0.375,0.198 10 false IMI 1.396,1.396 1.854,1.594 0.458,0.198 10 false IMO 1.01,1.979 1.469,2.177 0.458,0.198 10 false A62 1.021,2.156 1.479,2.354 0.458,0.198 10 false ECM 1.781,0.802 2.156,1 0.375,0.198 10 false 28 1.771,1.271 2.146,1.469 0.375,0.198 10 false 29 5.188,0.802 5.563,1 0.375,0.198 10 false 13 5.188,1.271 5.563,1.469 0.375,0.198 10 false 14

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the certification ECU (smart key ECU assembly), refer to the registration.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>REGISTRATION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When DTC B2799 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ECM)
a.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-14 (EFII) - A62-29 (IMO) Always Below 1 Ω
A62-29 (IMO) - Body ground Always 10 kΩ or higher
G82-14 (EFII) - Body ground Always 10 kΩ or higher
G82-13 (EFIO) - A62-28 (IMI) Always Below 1 Ω
A62-28 (IMI) - Body ground Always 10 kΩ or higher
G82-13 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REGISTER ECU COMMUNICATION ID

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REGISTER ECU COMMUNICATION ID

Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
B2799 is not output
B2799 is output
Other DTCs are output



B2799 is not output

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

B2799 is output

5.REPLACE ECM

Other DTCs are output

5.REPLACE ECM
a.

Temporarily replace the ECM with a new one.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.REGISTER ECU COMMUNICATION ID
6.REGISTER ECU COMMUNICATION ID

Result:
Proceed to
NEXT



NEXT

7.CLEAR DTC
7.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
DTC B2799 is not output
DTC B2799 is output



DTC B2799 is not output

END (ECM WAS DEFECTIVE)

DTC B2799 is output

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)