Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Key System)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0059577 IMMOBILISER SYSTEM(w/ Smart Key System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Key System)  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

When the communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A Theft Deterrent System Communication Line High Fixation The communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high (1 trip detection logic*).
·

Harness or connector

·

Certification ECU (smart key ECU assembly

·

ECM


DTC output confirmation operation:

Turn the engine switch on (IG) and wait 10 seconds.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A -

WIRING DIAGRAM

B344499
5.156,2.083 6.646,2.438 1.49,0.354 10 false Certification ECU (Smart Key ECU Assembly) 5.156,1.927 5.615,2.125 0.458,0.198 10 false G82 5.51,1.135 5.969,1.333 0.458,0.198 10 false EFIO 1.479,1.135 1.823,1.333 0.344,0.198 10 false IMI 1.115,1.979 1.458,2.177 0.344,0.198 10 false A62 1.115,2.135 1.458,2.333 0.344,0.198 10 false ECM 1.823,1 2.167,1.198 0.344,0.198 10 false 28 5.24,1.021 5.583,1.219 0.344,0.198 10 false 13

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the certification ECU (smart key ECU assembly), refer to the registration.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>REGISTRATION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



HINT:

When DTC B279A and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

If DTCs other than DTC B279A are output, troubleshoot those DTCs first.



Result:
Proceed to
DTC B279A is not output
DTC B279A and other DTCs are output



DTC B279A is not output

3.CHECK CONNECTION OF CONNECTOR

DTC B279A and other DTCs are output

3.CHECK CONNECTION OF CONNECTOR
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the ECM and certification ECU (smart key ECU assembly).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ECM)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ECM)
a.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-13 (EFIO) - A62-28 (IMI) Always Below 1 Ω
A62-28 (IMI) - Body ground Always 10 kΩ or higher
G82-13 (EFIO) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A62-28 (IMI) - Body ground Always Below 1 V
G82-13 (EFIO) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

5.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>CERTIFICATION ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.REGISTER RECOGNITION CODES
6.REGISTER RECOGNITION CODES

Result:
Proceed to
NEXT



NEXT

7.REGISTER ECU COMMUNICATION ID
7.REGISTER ECU COMMUNICATION ID

Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Key System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
DTC B279A is not output
DTC B279A is output



DTC B279A is not output

END (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] WAS DEFECTIVE)

DTC B279A is output