Home › Brake › PARKING BRAKE › PARKING BRAKE ASSEMBLY
RM30B0U _54 Brake _011370 PARKING BRAKE _0059599 PARKING BRAKE ASSEMBLY A

PARKING BRAKE  PARKING BRAKE ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.APPLY HIGH TEMPERATURE GREASE

a.
C278503
1.521,1.896 1.521,1.792 false
V100135

High-temperature grease


Apply a light coat of high-temperature grease to the areas of the backing plate that contact the shoes.


Hide 2.INSTALL PARKING BRAKE SHOE LEVER LH

Hide 3.INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH

a.

Connect the parking brake cable to the parking brake shoe lever.


b.
C278504
1.854,0.625 1.781,0.74 false
V100135

High-temperature grease


Apply a light coat of high-temperature grease to the following contact surfaces of the No. 2 parking brake shoe.

·

Shoe to anchor pin

·

Shoe to parking brake lever pin

·

Shoe to spring



c.
C278499

Install the shoe with the shoe hold-down spring and shoe hold-down spring pin.


Hide 4.INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH

a.
C278505
1.76,1.656 1.823,1.552 false
V100135

High-temperature grease


Apply a light coat of high-temperature grease to the following contact surfaces of the No. 1 parking brake shoe.

·

Shoe to anchor pin

·

Shoe to spring



b.
C278498

Install the shoe with the shoe hold-down spring and shoe hold-down spring pin.


Hide 5.INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET

a.
C278506
2.344,1.906 2.521,1.854 false
V100144

High-temperature grease


Apply a light coat of high-temperature grease to the areas of the shoe adjusting screw set shown in the illustration.


b.

Install the shoe adjusting screw set.


Hide 6.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Lower Side)

a.

Using needle-nose pliers, install the shoe return tension spring.


Hide 7.INSTALL PARKING BRAKE SHOE STRUT LH

a.
C278507
2.26,0.854 2.313,0.771 false
V100135

High-temperature grease


Apply a light coat of high-temperature grease to the contact surface of the parking brake shoe strut and shoe return tension spring.


b.

Install the parking brake shoe strut.


Hide 8.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Upper Side)

a.
C278497

Using needle-nose pliers, install the 2 shoe return tension springs.


Hide 9.CHECK PARKING BRAKE INSTALLATION

a.

Check that each part is installed properly.

C278508
0.396,0.115 0.771,0.354 0.375,0.24 12 *A 4.26,0.115 4.635,0.354 0.375,0.24 12 *B

Text in Illustration
*A for LH Side *B for RH Side
V100135

Front - -

NOTICE:

There should be no oil or grease adhering to the friction surfaces of the shoe lining and disc.



Hide 10.INSTALL REAR DISC

Hide 11.CHECK PARKING BRAKE LEVER TRAVEL

Hide 12.ADJUST PARKING BRAKE LEVER TRAVEL

Hide 13.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 14.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 15. SETTLE PARKING BRAKE SHOE AND DISC

a.

Pull the parking brake lever with a force of 147 N (15 kgf, 33 lbf).


b.

Drive the vehicle at approximately 50 km/h (31 mph) for approximately 400 m (0.25 miles).

NOTICE:

Drive the vehicle on a safe, level and dry road.



c.

Repeat the above steps 2 or 3 times.