The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 1 indoor electrical key antenna assembly (front floor). For the No. 1 indoor electrical key antenna assembly (front floor) to detect when the electrical key transmitter sub-assembly is inside the vehicle, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the vehicle. DTC B27A5 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (front floor) (between terminals CLG5 and ANTE5, or terminals CG5B and CLGB).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| B27A5 | Open in Front Floor Electrical Key Oscillator Circuit | An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (front floor) (CLG5 - ANTE5, CG5B - CLGB) (1 trip detection logic*). | ·
Harness or connector ·
No. 1 indoor electrical key antenna assembly (front floor) ·
Certification ECU (smart key ECU assembly) |
Any time |
*: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
When electrical key transmitter sub-assembly is in front seat area:
·
Power source mode does not change when engine switch pressed ·
Electrical key transmitter sub-assembly locked inside vehicle |
- |
| DTC Code | Data List and Active Test |
|---|---|
| B27A5 | Key diagnostic mode can be used to perform troubleshooting |
The smart key system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the Techstream with the vehicle engine switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart key system (for Entry Function) precaution.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>PRECAUTION
After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
The No. 1 indoor electrical key antenna assembly (front floor) has an antenna coil between ANTE5 and CLGB terminals.
Turn the engine switch off.
Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (front floor).
Connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G82 and G84 certification ECU (smart key ECU assembly) connectors.
Disconnect the G45 No. 1 indoor electrical key antenna assembly (front floor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G84-3 (CLG5) - G45-1 (ANTE5) | Always | Below 1 Ω |
| G84-2 (CG5B) - G45-3 (CLGB) | Always | Below 1 Ω |
| G82-11 (E) - Body ground | Always | Below 1 Ω |
| G84-3 (CLG5) or G45-1 (ANTE5) - Body ground | Always | 10 kΩ or higher |
| G84-2 (CG5B) or G45-3 (CLGB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the G82 and G84 certification ECU (smart key ECU assembly) connectors.
| *a | Component with harness connected
(Certification ECU [Smart Key ECU Assembly]) |
*b | Waveform |
| *c | Within approximately 30 seconds from when the door is closed | *d | After approximately 30 seconds from when the door is closed |
Connect the G45 No. 1 indoor electrical key antenna assembly (front floor) connector.
Using an oscilloscope, check the waveform.
| Tester Connection | Switch Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| G84-3 (CLG5) - G82-11 (E) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
2 V/DIV., 500 ms/DIV. | Pulse generation
(See waveform) |
| G84-2 (CG5B) - G82-11 (E) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
2 V/DIV., 500 ms/DIV. | Pulse generation
(See waveform) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the No. 1 indoor electrical key antenna assembly (front floor) with a new or known good one.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Proceed to |
|---|
| DTC B27A5 is not output |
| DTC B27A5 is output |
DTC B27A5 is not output
DTC B27A5 is output