Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM(for Entry Function)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0058004 SMART KEY SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART KEY SYSTEM(for Entry Function)  B27A7  Open in Inside Luggage Compartment Electrical Key Oscillator Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 3 indoor electrical key antenna assembly (inside luggage). For the No. 3 indoor electrical key antenna assembly (inside luggage) to detect when the electrical key transmitter sub-assembly is inside the luggage, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the luggage. DTC B27A7 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (inside luggage) (between terminals CLG7 and ANTE7, or terminals CG7B and CLGB).

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B27A7 Open in Inside Luggage Compartment Electrical Key Oscillator Circuit An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (inside luggage) (CLG7 - ANTE7, CG7B - CLGB) (1 trip detection logic*).
·

Harness or connector

·

No. 3 indoor electrical key antenna assembly (inside luggage)

·

Certification ECU (smart key ECU assembly)


Any time

*: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
When electrical key transmitter sub-assembly is inside luggage area:
·

Power Source mode does not change when engine switch pressed

·

Electrical key transmitter sub-assembly becomes locked inside vehicle


-

Related Data List and Active Test
DTC Code Data List and Active Test
B27A7 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B320942
1.344,0.448 1.854,0.729 0.51,0.281 10 ANTE7 1.417,0.917 2.031,1.167 0.615,0.25 10 CLGB 0.292,1.375 0.719,1.719 0.427,0.344 10 M21 1.896,0.792 2.115,0.99 0.219,0.198 10 3 1.896,0.344 2.25,0.625 0.354,0.281 10 1 5.521,0.458 6.021,0.781 0.5,0.323 10 CLG7 5.521,0.917 6.094,1.167 0.573,0.25 10 CG7B 5.521,1.385 5.771,1.615 0.25,0.229 10 E 5.24,0.281 5.563,0.563 0.323,0.281 10 9 5.25,0.729 5.521,0.99 0.271,0.26 10 8 5.208,1.198 5.438,1.375 0.229,0.177 10 11 5.198,1.833 6.75,2.271 1.552,0.438 10 Certification ECU (Smart Key ECU Assembly) 0.292,1.531 2.521,2.063 2.229,0.531 10 No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage) 5.167,0.917 5.49,1.104 0.323,0.188 10 G83 5.167,0.458 5.531,0.667 0.365,0.208 10 G83 5.167,1.375 5.521,1.594 0.354,0.219 10 G82

CAUTION / NOTICE / HINT

NOTICE:
·

The smart key system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the Techstream with the vehicle engine switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart key system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The No. 3 indoor electrical key antenna assembly (inside luggage) has an antenna coil between ANTE7 and CLGB terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (inside luggage).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY AND BODY GROUND)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY AND BODY GROUND)
a.

Disconnect the G82 and G83 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the M21 No. 3 indoor electrical key antenna assembly (inside luggage) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G83-9 (CLG7) - M21-1 (ANTE7) Always Below 1 Ω
G83-8 (CG7B) - M21-3 (CLGB) Always Below 1 Ω
G82-11 (E) - Body ground Always Below 1 Ω
G83-9 (CLG7) or M21-1 (ANTE7) - Body ground Always 10 kΩ or higher
G83-8 (CG7B) or M21-3 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY)
a.

Connect the G82 and G83 certification ECU (smart key ECU assembly) connectors.

B282013
2.135,0.542 2.51,0.771 0.375,0.229 3.354,0.542 3.729,0.771 0.375,0.229 3.698,1.417 3.448,2.146 false 2.719,1.531 2.531,2.052 false 3.792,1.417 4.042,2.146 false 1.167,2.76 1.385,2.958 0.219,0.198 10 *b 0.208,0.156 0.427,0.354 0.219,0.198 10 *a 0.917,3.625 1.281,3.792 0.365,0.167 10 GND 2.198,4.365 2.417,4.563 0.219,0.198 10 *c 3.031,4.365 3.25,4.563 0.219,0.198 10 *d 2.458,2.073 2.594,2.24 0.135,0.167 10 E 3.229,2.198 3.719,2.365 0.49,0.167 10 CLG7 3.938,2.188 4.458,2.354 0.521,0.167 10 CG7B 2.177,0.573 2.5,0.833 0.323,0.26 10 G82 3.406,0.573 3.844,0.875 0.438,0.302 10 G83
*a Component with harness connected
(Certification ECU [Smart Key ECU Assembly])
*b Waveform
*c Before driver door lock sensor touched *d After driver door lock sensor touched



b.

Connect the M21 No. 3 indoor electrical key antenna assembly (inside luggage) connector.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
G83-9 (CLG7) - G82-11 (E)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform)
G83-8 (CG7B) - G82-11 (E)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

4.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE)
a.

Temporarily replace the No. 3 indoor electrical key antenna assembly (inside luggage) with a new or known good one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Luggage Compartment)>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Smart Key > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Smart Key > Trouble Codes
50001 125

Result:
Proceed to
DTC B27A7 is not output
DTC B27A7 is output



DTC B27A7 is not output

END (NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [INSIDE LUGGAGE] WAS DEFECTIVE)

DTC B27A7 is output

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)