Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM(for Entry Function)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0058004 SMART KEY SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART KEY SYSTEM(for Entry Function)  B27A8  Open in Outside Luggage Compartment Electrical Key Antenna Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the electrical key antenna (outside luggage). For the electrical key antenna (outside luggage) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, the received request signal is transmitted within approximately 1.0 m (3.28 ft.) of the back door. DTC B27A8 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage) (between terminals CLG8 and ANTE8, or terminals CG8B and CLGB).

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B27A8 Open in Outside Luggage Compartment Electrical Key Antenna Circuit An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage) (CLG8 - ANTE8, CG8B - CLGB) (1 trip detection logic*).
·

Electrical key antenna (outside luggage)

·

Electrical key antenna (outside luggage)

·

Certification ECU (smart key ECU assembly)


Any time

*: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry unlock operation cannot be performed for back door -

Related Data List and Active Test
DTC Code Data List and Active Test
B27A8 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B320942
1.26,0.458 1.865,0.698 0.604,0.24 10 ANTE8 1.323,0.917 1.823,1.146 0.5,0.229 10 CLGB 0.594,1.417 0.917,1.635 0.323,0.219 10 T2 1.896,0.76 2.198,1.125 0.302,0.365 10 2 1.896,0.313 2.104,0.563 0.208,0.25 10 1 5.5,0.458 6.063,0.833 0.563,0.375 10 CLG8 5.5,0.917 6.188,1.198 0.688,0.281 10 CG8B 5.51,1.375 5.854,1.698 0.344,0.323 10 E 5.24,0.271 5.417,0.5 0.177,0.229 10 2 5.24,0.74 5.552,1.021 0.313,0.281 10 1 5.208,1.188 5.49,1.385 0.281,0.198 10 11 5.198,1.844 7.031,2.49 1.833,0.646 10 Certification ECU (Smart Key ECU Assembly) 0.583,1.604 2.365,2.229 1.781,0.625 10 Electrical Key Antenna (Outside Luggage) 5.146,0.917 5.49,1.188 0.344,0.271 10 G83 5.135,0.458 5.51,0.823 0.375,0.365 10 G83 5.135,1.375 5.625,1.542 0.49,0.167 10 G82

CAUTION / NOTICE / HINT

NOTICE:
·

The smart key system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the Techstream with the vehicle engine switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart key system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The electrical key antenna (outside luggage) has an antenna coil between ANTE8 and CLGB terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU AND BODY GROUND)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU AND BODY GROUND)
a.

Disconnect the G82 and G83 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the T2 electrical key antenna (outside luggage) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G83-2 (CLG8) - T2-1 (ANTE8) Always Below 1 Ω
G83-1 (CG8B) - T2-2 (CLGB) Always Below 1 Ω
G82-11 (E) - Body ground Always Below 1 Ω
G83-2 (CLG8) or T2-1 (ANTE8) - Body ground Always 10 kΩ or higher
G83-1 (CG8B) or T2-2 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)
a.
B226391
1.823,1.073 2.219,0.708 2.219,0.708 2.406,0.708 false 1.594,1.083 1.198,0.719 1.198,0.719 1.021,0.719 false 2.469,0.615 3.01,0.813 0.542,0.198 10 CLGB 0.417,0.635 0.99,0.823 0.573,0.188 10 ANTE8

Remove the electrical key antenna (outside luggage).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Outside Luggage Compartment)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ANTE8) - 2 (CLGB) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>CERTIFICATION ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Smart Key > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Smart Key > Trouble Codes
50001 125

Result:
Proceed to
DTC B27A8 is not output
DTC B27A8 is output



DTC B27A8 is not output

END (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] WAS DEFECTIVE)

DTC B27A8 is output