Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM30B0U _57 Power Source / Network _009133 NETWORKING _0059674 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2321  Driver Side Door ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the front power window regulator motor assembly LH and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2321 Driver Side Door ECU Communication Stop No communication between the front power window regulator motor assembly (driver side) and main body ECU for 10 seconds or more.
·

Front power window regulator motor assembly LH

·

Main body ECU (multiplex network body ECU)

·

Harness or connector

·

Instrument panel junction block assembly



WIRING DIAGRAM

B339323
1.667,1.542 3.292,2.01 1.625,0.469 10 false Instrument Panel Junction Block Assembly 1.656,1.354 1.969,1.552 0.313,0.198 10 false 3D 2.604,2.594 3.427,2.875 0.823,0.281 10 false from Battery 1.177,0.927 1.625,1.146 0.448,0.219 10 false LIN2 1.552,0.771 1.865,0.969 0.313,0.198 10 false 16 3.563,0.771 3.875,0.969 0.313,0.198 10 false 54 0.292,2.531 1.938,3.01 1.646,0.479 10 false Main Body ECU (Multiplex Network Body ECU) 0.292,2.333 0.448,2.531 0.156,0.198 10 false A 0.708,4.448 2.406,4.708 1.698,0.26 10 false : LIN Communication Line 5.156,0.896 5.615,1.094 0.458,0.198 10 false LIN 4.948,0.76 5.104,0.958 0.156,0.198 10 false 9 5.146,2.594 5.302,2.792 0.156,0.198 10 false B 4.948,2.469 5.104,2.667 0.156,0.198 10 false 2 5.646,2.594 6.042,2.844 0.396,0.25 10 false GND 6.115,2.479 6.271,2.677 0.156,0.198 10 false 1 4.656,3.302 6.573,3.677 1.917,0.375 10 false Front Power Window Regulator Motor Assembly LH 4.635,3.094 5.396,3.333 0.76,0.24 10 false J3 4.021,2.813 4.938,3.01 0.917,0.198 10 false DOOR D

CAUTION / NOTICE / HINT

NOTICE:
·

When using the Techstream with the ignition switch off to troubleshoot:

Connect the Techstream to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When the front power window regulator motor assembly (driver side) is removed and reinstalled or replaced, the front power window regulator motor assembly (driver side) must be initialized.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>INITIALIZATION



HINT:

When DTC B2321 and B2325 are output simultaneously, perform troubleshooting for DTC B2325 first.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>B2325


PROCEDURE

1.CLEAR DTC

Body Electrical > Main Body > Clear DTCs
50002 123
Result:
Result
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Proceed to
DTC B2321 is output
DTC B2321 is not output



DTC B2321 is output

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

DTC B2321 is not output

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Disconnect the J3 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - J3-9 (LIN) Always Below 1 Ω
A-16 (LIN2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)

NG

7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
4.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)
B301170
1.552,0.24 1.896,0.479 0.344,0.24 1.021,1.417 1.521,1.146 false 2.458,1.396 1.917,1.146 false 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 2.563,1.344 2.719,1.542 0.156,0.198 10 false B 0.635,1.344 1.125,1.552 0.49,0.208 10 false GND 1.646,0.271 1.958,0.469 0.313,0.198 10 false J3
*a Front view of wire harness connector
(to Front Power Window Regulator Motor Assembly LH)


a.

Disconnect the J3 front power window regulator motor assembly LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J3-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J3-2 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Temporarily replace the front power window regulator motor assembly LH with a new or normally functioning one.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Proceed to
DTC B2321 is not output
DTC B2321 is output



DTC B2321 is not output

END (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH IS DEFECTIVE)

DTC B2321 is output

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Disconnect the J3 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-54 - J3-9 (LIN) Always Below 1 Ω
3D-54 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR