The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0705 | Transmission Range Sensor Circuit Malfunction (PRNDL Input) | One of the following conditions (A) through (C) is met (2-trip detection logic)
(A) Either of the following conditions 1, 2 or 3 is met: 1. Any 2 or more signals of the following are ON simultaneously: ·
P input signal is ON. ·
R input signal is ON. ·
D input signal is ON. 2. Any 2 or more signals of the following are ON simultaneously: ·
N input signal is ON. ·
R input signal is ON. ·
D input signal is ON. 3. Any 2 or more signals of the following are ON simultaneously: ·
NSW input signal is ON. ·
R input signal is ON. ·
D input signal is ON. (B) All switches are OFF simultaneously for P, N, NSW, R and D. (C) When any of following conditions is met for 2.0 sec. or more in the S position: ·
P input signal is ON. ·
N input signal is ON. ·
NSW input signal is ON. ·
R input signal is ON. |
·
Open or short in park/neutral position switch assembly circuit ·
Park/neutral position switch assembly ·
Transmission control switch (transmission floor shift assembly) ·
ECM |
Comes on | DTC stored |
These DTCs indicate a problem with the park/neutral position switch assembly and the wire harness in the park/neutral position switch assembly circuit.
The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.
For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, N, NSW, R, D or S). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will turn on the MIL and store the DTC.
| Related DTCs | P0705: Park/neutral position switch/Verify switch input |
| Required sensors/Components | Park/neutral position switch assembly |
| Frequency of operation | Continuous |
| Duration | Condition (A) and (C): 2 sec.
Condition (B): 60 sec. |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not stored | None |
| Battery voltage | 8 V or higher |
| Ignition switch | ON |
| Starter | OFF |
One of the following conditions is met: Condition (A), (B) or (C)
| Any two of the following conditions are met: | Conditions 1, 2 and 3 |
| 1. One of the following conditions is met: | Conditions (a), (b) or (c) |
| (a). P position switch | ON |
| (b). N position switch | ON |
| (c). Park/neutral position switch (NSW) | ON |
| 2. R position switch | ON |
| 3. D position switch | ON |
All of the following conditions are met
| P position switch | OFF |
| N position switch | OFF |
| Park/neutral position switch (NSW) | OFF |
| R position switch | OFF |
| D position switch | OFF |
When the shift lever is in S, one of the following conditions is met
| P position switch | ON |
| N position switch | ON |
| Park/neutral position switch (NSW) | ON |
| R position switch | ON |
| Park/neutral position switch assembly | The park/neutral position switch sends only one signal to the ECM |
Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION
Perform the universal trip to clear permanent DTCs.
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR
DATA LIST
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral Position SW Signal | PNP switch status | ON or OFF | ·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (P Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in P ·
OFF: Shift lever not in P |
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (R Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in R ·
OFF: Shift lever not in R |
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (N Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in N ·
OFF: Shift lever not in N |
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Sports Mode Selection SW | Sport mode select switch status | ON or OFF | ·
ON: Shift lever in S, "+" or "-" ·
OFF: Shift lever not in S, "+" or "-" |
- |
| Shift SW Status (D Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in D or S ·
OFF: Shift lever not in D or S |
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Tester Display |
|---|
| Neutral Position SW Signal |
| Shift SW Status (P Range) |
| Shift SW Status (R Range) |
| Shift SW Status (N Range) |
| Sports Mode Selection SW |
| Shift SW Status (D Range) |
Disconnect the park/neutral position switch connector.
| *a | Front view of wire harness connector
(to Park/Neutral Position Switch Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B36-1 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| B36-1 (RB) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the park/neutral position switch connector.
| *a | Front view of wire harness connector
(to Park/Neutral Position Switch Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B36-4 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| B36-4 (B) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the park/neutral position switch connector.
| *a | Component without harness connected
(Park/Neutral Position Switch Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
·
1 (RB) - 3 (PL) ·
4 (B) - 9 (L) |
Shift lever in P | Below 1 Ω |
| 1 (RB) - 2 (RL) | Shift lever in R | Below 1 Ω |
·
1 (RB) - 8 (NL) ·
4 (B) - 9 (L) |
Shift lever in N | Below 1 Ω |
| 1 (RB) - 7 (DL) | ·
Shift lever in D ·
Shift lever in S, "+" or "-" |
Below 1 Ω |
·
1 (RB) - 3 (PL) ·
4 (B) - 9 (L) |
Shift lever not in P | 10 kΩ or higher |
| 1 (RB) - 2 (RL) | Shift lever not in R | 10 kΩ or higher |
·
1 (RB) - 8 (NL) ·
4 (B) - 9 (L) |
Shift lever not in N | 10 kΩ or higher |
| 1 (RB) - 7 (DL) | ·
Shift lever not in D ·
Shift lever not in S, "+" or "-" |
10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
Disconnect the transmission control switch connector.
| *a | Front view of wire harness connector
(to Transmission Control Switch) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G36-4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| G36-4 (IG) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the transmission control switch connector.
| *a | Component without harness connected
(Transmission Control Switch) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (IG) - 5 (S) | Shift lever in S, "+" or "-" | Below 1 Ω |
| 4 (IG) - 5 (S) | Shift lever not in S, "+"or "-" | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connectors.
| *a | Front view of wire harness connector
(to ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B77-70 (P) - Body ground | ·
Ignition switch ON ·
Shift lever in P |
11 to 14 V |
| B77-66 (R) - Body ground | ·
Ignition switch ON ·
Shift lever in R |
11 to 14 V* |
| B77-71 (N) - Body ground | ·
Ignition switch ON ·
Shift lever in N |
11 to 14 V |
| B77-67 (D) - Body ground | ·
Ignition switch ON ·
Shift lever in D |
11 to 14 V |
| A62-27 (S) - Body ground | ·
Ignition switch ON ·
Shift lever in S, "+"or "-" |
11 to 14 V |
| B77-70 (P) - Body ground | ·
Ignition switch ON ·
Shift lever not in P |
Below 1 V |
| B77-66 (R) - Body ground | ·
Ignition switch ON ·
Shift lever not in R |
Below 1 V |
| B77-71 (N) - Body ground | ·
Ignition switch ON ·
Shift lever not in N |
Below 1 V |
| B77-67 (D) - Body ground | ·
Ignition switch ON ·
Shift lever not in D |
Below 1 V |
| A62-27 (S) - Body ground | ·
Ignition switch ON ·
Shift lever not in S, "+" or "-" |
Below 1 V |
*: The voltage will drop slightly due to the illumination of the back-up light.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B36 park/neutral position switch connector.
Disconnect the B77 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B36-4 (B) - B77-63 (NSW) | Always | Below 1 Ω |
| B36-4 (B) - Body ground | Always | 10 kΩ or higher |
| B77-63 (NSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG