Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR
RM30B0U _59 Vehicle Exterior _011369 MIRROR (EXT) _0060870 OUTER REAR VIEW MIRROR G

MIRROR (EXT)  OUTER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

a.

Check the operation of the mirror surface.

i.
B199929
2.104,2.698 2.594,2.698 true 1.969,2.646 2.365,2.354 2.365,2.354 2.604,2.354 true 1.865,2.646 2.24,2 2.24,2 2.615,2 true 0.229,0.208 0.417,0.365 0.188,0.156 10 *a 2.667,1.927 2.917,2.083 0.25,0.156 10 MH 2.656,2.281 2.906,2.438 0.25,0.156 10 M+ 2.646,2.615 2.896,2.771 0.25,0.156 10 MV
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 6 (MV)
Battery negative (-) → Terminal 5 (M+)
Turns upward
Battery positive (+) → Terminal 5 (M+)
Battery negative (-) → Terminal 6 (MV)
Turns downward
Battery positive (+) → Terminal 4 (MH)
Battery negative (-) → Terminal 5 (M+)
Turns left
Battery positive (+) → Terminal 5 (M+)
Battery negative (-) → Terminal 4 (MH)
Turns right


If the result is not as specified, replace the outer mirror retractor LH.



b.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.



i.
B199933
0.75,2.594 1.417,2.594 1.417,2.594 1.573,2.75 true 0.74,3.115 1.438,3.115 1.438,3.115 1.583,2.99 true 0.167,0.115 0.354,0.271 0.188,0.156 10 *a 1.25,0.063 1.375,0.219 0.125,0.156 10 A 0.927,0.813 1.052,0.969 0.125,0.156 10 B 1.094,1.583 1.219,1.74 0.125,0.156 10 C 1.49,1.844 1.615,2 0.125,0.156 10 D 1.813,2.021 1.938,2.177 0.125,0.156 10 E 0.469,2.521 0.719,2.677 0.25,0.156 10 MR 0.469,3.042 0.719,3.198 0.25,0.156 10 MF
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Measurement Condition Mirror Position Specified Condition
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Forward position A Moves from A to retracted position E
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Forward position A Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Position between forward position A and driving position C Moves from B to retracted position E
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between forward position A and driving position C Moves from B to forward position A
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Driving position C Moves from C to retracted position E
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Driving position C Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Position between driving position C and retracted position E Moves from D to retracted position E
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between driving position C and retracted position E Moves from D to driving position C
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Retracted position E Does not move
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Retracted position E Moves from E to driving position C


If the result is not as specified, replace the outer mirror retractor LH.



c.

Check the operation of the mirror heater.

i.
B242855
0.677,2.458 1.146,2.458 1.146,2.458 1.385,2.708 true 0.656,3.125 1.167,3.125 1.167,3.125 1.375,2.948 true 0.375,0.271 0.542,0.448 0.167,0.177 10 *a 0.552,2.375 0.656,2.552 0.104,0.177 10 + 0.531,3.031 0.635,3.208 0.104,0.177 10 -
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+) - 8 (-) 25°C (75°F) 5.4 to 8.1 Ω


If the result is not as specified, check the outer rear view mirror sub-assembly LH (Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION).

If the result is not as specified, replace the outer mirror retractor LH.


iii.

Connect the cable from the positive (+) battery terminal to terminal 2 and the negative (-) battery terminal to terminal 8, and then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, check the outer rear view mirror sub-assembly LH (Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION).

If the result is not as specified, replace the outer mirror retractor LH.



d.
B319246
2.521,1.802 2.115,1.802 2.115,1.802 2.115,1.323 true 1.458,1.792 1.938,1.792 1.938,1.792 1.938,1.333 true 0.396,0.25 0.573,0.406 0.177,0.156 10 *a 1.313,1.708 1.438,1.865 0.125,0.156 10 B 2.573,1.719 2.698,1.875 0.125,0.156 10 E
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the side turn signal light assembly LH.

i.

Apply battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Measurement Connection Specified Condition
Battery positive (+) → Terminal 10 (B)
Battery negative (-) → Terminal 11 (E)
Side turn light illuminates


If the result is not as specified, check the side turn signal light assembly LH (Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION).

If the result is not as specified, replace the outer mirror retractor LH.



Hide 2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

a.

Check the operation of the mirror surface.

i.
B199928
1.854,2.646 2.156,1.896 2.156,1.896 2.573,1.896 true 1.969,2.646 2.271,2.198 2.271,2.198 2.542,2.198 true 2.083,2.646 2.365,2.5 2.365,2.5 2.521,2.5 true 2.573,2.427 2.844,2.573 0.271,0.146 10 MV 2.604,2.125 2.833,2.271 0.229,0.146 10 M+ 2.625,1.802 2.896,1.948 0.271,0.146 10 MH 0.177,0.146 0.365,0.313 0.188,0.167 10 *a
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 6 (MV)
Battery negative (-) → Terminal 5 (M+)
Turns upward
Battery positive (+) → Terminal 5 (M+)
Battery negative (-) → Terminal 6 (MV)
Turns downward
Battery positive (+) → Terminal 4 (MH)
Battery negative (-) → Terminal 5 (M+)
Turns left
Battery positive (+) → Terminal 5 (M+)
Battery negative (-) → Terminal 4 (MH)
Turns right


If the result is not as specified, replace the outer mirror retractor RH.



b.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.



i.
B199932
1.563,2.74 1.49,2.604 1.49,2.604 0.906,2.604 true 1.563,3 1.521,3.188 1.521,3.188 0.906,3.188 true 0.646,2.531 0.958,2.719 0.313,0.188 10 MR 0.677,3.104 0.906,3.292 0.229,0.188 10 MF 2.063,0 2.229,0.177 0.167,0.177 10 A 2.396,0.74 2.573,0.917 0.177,0.177 10 B 2.198,1.646 2.323,1.802 0.125,0.156 10 C 1.823,1.885 1.958,2.063 0.135,0.177 10 D 1.458,2.083 1.583,2.25 0.125,0.167 10 E 0.271,0.292 0.427,0.448 0.156,0.156 10 *a
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Measurement Condition Mirror Position Specified Condition
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Forward position A Moves from A to retracted position E
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Forward position A Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Position between forward position A and driving position C Moves from B to retracted position E
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between forward position A and driving position C Moves from B to forward position A
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Driving position C Moves from C to retracted position E
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Driving position C Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Position between driving position C and retracted position E Moves from D to retracted position E
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between driving position C and retracted position E Moves from D to driving position C
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Retracted position E Does not move
Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)
Retracted position E Moves from E to driving position C


If the result is not as specified, replace the outer mirror retractor RH.



c.

Check the operation of the mirror heater.

i.
B242856
1.385,2.625 1.229,2.396 1.229,2.396 0.948,2.396 true 1.385,2.906 1.198,3.167 1.198,3.167 0.948,3.167 true 0.813,2.313 0.969,2.479 0.156,0.167 10 + 0.854,3.073 0.958,3.271 0.104,0.198 10 - 0.417,0.292 0.604,0.448 0.188,0.156 10 *a
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+) - 8 (-) 25°C (75°F) 5.4 to 8.1 Ω


If the result is not as specified, check the outer rear view mirror sub-assembly RH (Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION)

If the result is not as specified, replace the outer mirror retractor RH.


iii.

Connect the cable from the positive (+) battery terminal to terminal 2 and the negative (-) battery terminal to terminal 8, and then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, check the outer rear view mirror sub-assembly RH (Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION).

If the result is not as specified, replace the outer mirror retractor RH.



d.
B319246
1.458,1.771 1.938,1.771 1.938,1.771 1.938,1.323 true 2.594,1.771 2.125,1.771 2.125,1.771 2.125,1.323 true 1.313,1.698 1.417,1.896 0.104,0.198 10 B 2.667,1.698 2.802,1.875 0.135,0.177 10 E 0.281,0.198 0.469,0.354 0.188,0.156 10 *a
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the side turn signal light assembly RH.

i.

Apply battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Measurement Connection Specified Condition
Battery positive (+) → Terminal 10 (B)
Battery negative (-) → Terminal 11 (E)
Side turn light illuminates


If the result is not as specified, check the side turn signal light assembly RH (Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION).

If the result is not as specified, replace the outer mirror retractor RH.