When the back door closer does not operate, one of the following may be the cause: 1) improper fit of the back door, or a foreign object is stuck in the back door, 2) initialization of the multiplex network door ECU, 3) a malfunction in the multiplex network door ECU power source circuit, 4) a malfunction in the back door lock assembly circuit, or 5) a malfunction in the multiplex network door ECU.
Inspect fuses for circuits related to this system before performing the following inspection procedure.
Check for DTCs.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC is not output |
| DTC B2250 is output |
| DTC B2251 is output |
DTC is not output
DTC B2250 is output
DTC B2251 is output
Check if the back door can be fully closed by hand.
| Proceed to |
|---|
| The back door can be closed normally |
| The back door cannot be closed normally |
The back door can be closed normally
The back door cannot be closed normally
Perform the initialization of the multiplex network door ECU.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Check the back door closer operation.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>OPERATION CHECK
| Proceed to |
|---|
| The back door closer operates normally |
| The back door closer operates not normally |
The back door closer operates normally
The back door closer operates not normally
| *a | Rear view of wire harness connector
(to Multiplex Network Door ECU) |
Disconnect the multiplex network door ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U19-7 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U18-1 (ECUB) - Body ground | Always | 11 to 14 V |
| U19-8 (B) - Body ground | Always | 11 to 14 V |
| U18-7 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| U18-7 (IG) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the back door lock assembly.
Inspect the back door lock assembly.
Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the U13 back door lock assembly connector.
Disconnect the U18 and U19 multiplex network door ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U13-1 (M+) - U19-10 (DC+) | Always | Below 1 Ω |
| U13-2 (M-) - U19-9 (DC-) | Always | Below 1 Ω |
| U13-3 (CTY) - U18-19 (FUL) | Always | Below 1 Ω |
| U13-5 (CLS) - U18-21 (HAF) | Always | Below 1 Ω |
| U13-6 (OPN) - U18-24 (POS) | Always | Below 1 Ω |
| U13-4 (E) - Body ground | Always | Below 1 Ω |
| U13-1 (M+) or U19-10 (DC+) - Body ground | Always | 10 kΩ or higher |
| U13-2 (M-) or U19-9 (DC-) - Body ground | Always | 10 kΩ or higher |
| U13-3 (CTY) or U18-19 (FUL) - Body ground | Always | 10 kΩ or higher |
| U13-5 (CLS) or U18-21 (HAF) - Body ground | Always | 10 kΩ or higher |
| U13-6 (OPN) or U18-24 (POS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG