Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM › 2012.12–2013.11
RM30B0U _56 Audio / Visual / Telematics _009404 PARK ASSIST / MONITORING _0062869 REAR VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  Reverse Signal Circuit  


DESCRIPTION

The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly.

WIRING DIAGRAM

E274463
5.76,1.875 6.375,2.073 0.615,0.198 10 false G143 5.802,2.063 7.021,2.427 1.219,0.365 10 false Radio and Display Receiver Assembly 2.917,1.604 5.406,1.833 2.49,0.229 10 false Park/Neutral Position Switch Assembly 2.917,1.448 3.375,1.646 0.458,0.198 10 false B36 2.094,1.208 2.865,1.406 0.771,0.198 10 false GAUGE 0.25,0.979 1.635,1.188 1.385,0.208 10 false from IG1 NO. 2 Relay 3.563,0.865 3.719,1.063 0.156,0.198 10 false 1 4.76,0.865 4.917,1.063 0.156,0.198 10 false 2 3.74,0.979 4.052,1.177 0.313,0.198 10 false RB 4.479,0.979 4.792,1.177 0.313,0.198 10 false RL 5.729,0.875 5.885,1.073 0.156,0.198 10 false 2 5.906,0.979 6.365,1.177 0.458,0.198 10 false REV

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK VEHICLE SIGNAL (DISPLAY CHECK MODE)
a.
E270655

Enter the "Function Check/Setting I" mode and select "Vehicle Signal".


b.

Check that the display changes between ON and OFF according to the shift lever position.

OK:
Shift Lever Position Display
R ON
Except R OFF


HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E140414
1.448,0.302 1.917,0.583 0.469,0.281 0.438,0.896 0.917,1.385 false 0.115,0.083 0.427,0.281 0.313,0.198 10 *a 0.083,0.813 0.542,1.01 0.458,0.198 10 REV 1.521,0.354 1.969,0.563 0.448,0.208 10 G143
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G143-2 (REV) - Body ground Ignition switch ON, shift lever in R 11 to 14 V
G143-2 (REV) - Body ground Ignition switch ON, shift lever not in R Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the G143 radio and display receiver assembly connector.


b.

Disconnect the B36 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-2 (REV) - B36-2 (RL) Always Below 1 Ω
G143-2 (REV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)
a.
E270424
1.479,0.281 1.885,0.51 0.406,0.229 1.073,1.771 1.26,1.771 1.26,1.771 1.604,1.135 true 1.542,0.313 2,0.51 0.458,0.198 10 B36 0.823,1.698 1.281,1.896 0.458,0.198 10 RB 0.104,0.083 0.563,0.281 0.458,0.198 10 *a
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B36-1 (RB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK (for U760E)
OK (for U760F)
NG



OK (for U760E)

OK (for U760F)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR