Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type) › from 2013.11
RM30B0U _56 Audio / Visual / Telematics _009404 PARK ASSIST / MONITORING _0103948 REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type) J

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type)  Reverse Signal Circuit  


DESCRIPTION

The navigation receiver assembly receives a reverse signal from the park/neutral position switch assembly.

WIRING DIAGRAM

E280619
5.24,1.802 6.531,2.188 1.292,0.385 10 false Navigation Receiver Assembly 5.229,1.615 5.844,1.813 0.615,0.198 10 false G143 3.271,1.49 3.885,1.688 0.615,0.198 10 false B36 3.271,1.667 4.656,2.073 1.385,0.406 10 false Park/Neutral Position Switch Assembly 5.427,0.958 6.042,1.156 0.615,0.198 10 false REV 4.104,0.958 4.323,1.156 0.219,0.198 10 false RL 3.448,0.958 3.667,1.156 0.219,0.198 10 false RB 3.25,0.854 3.396,1.052 0.146,0.198 10 false 1 4.417,0.844 4.563,1.042 0.146,0.198 10 false 2 5.208,0.854 5.354,1.052 0.146,0.198 10 false 2 2.052,1.135 2.698,1.344 0.646,0.208 10 false GAUGE 0.146,0.948 1.542,1.208 1.396,0.26 10 false from IG1 NO.2 Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK VEHICLE SIGNAL (DISPLAY CHECK MODE)
a.
E270655

Enter the "Function Check/Setting I" mode and select "Vehicle Signal".


b.

Check that the display changes between ON and OFF according to the shift lever position.

OK:
Shift Lever Position Display
R ON
Except R OFF


HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY AND BATTERY)

NG

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY AND BATTERY)
a.

Disconnect the B36 park/neutral position switch assembly connector.


b.

Disconnect the G143 navigation receiver assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B36-1 (RB) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B36-2 (RL) - G143-2 (REV) Always Below 1 Ω
B36-2 (RL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR