Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type) › from 2013.11
RM30B0U _56 Audio / Visual / Telematics _009404 PARK ASSIST / MONITORING _0103948 REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type) J

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type)  Image from Camera for Rear View Monitor is Abnormal  


DESCRIPTION

The display signal of the rear television camera assembly is transmitted to the navigation receiver assembly.

WIRING DIAGRAM

E280622
5.5,2.521 6.115,2.719 0.615,0.198 10 false G153 5.5,2.708 6.771,3.125 1.271,0.417 10 false Navigation Receiver Assembly 5.719,0.667 6.333,0.865 0.615,0.198 10 false CA+ 5.719,1.135 6.333,1.333 0.615,0.198 10 false V- 5.719,1.604 6.333,1.802 0.615,0.198 10 false V+ 5.719,2.083 6.333,2.281 0.615,0.198 10 false CGND 1,2.073 1.615,2.271 0.615,0.198 10 false CGND 1.094,1.583 1.427,1.792 0.333,0.208 10 false CV+ 1.104,1.115 1.448,1.323 0.344,0.208 10 false CV- 1.104,0.667 1.479,0.865 0.375,0.198 10 false CB+ 0.448,2.5 1.063,2.698 0.615,0.198 10 false U6 0.448,2.677 1.708,3.063 1.26,0.385 10 false Rear Television Camera Assembly 2.427,2.229 2.76,2.438 0.333,0.208 10 false * 3.542,2.229 3.875,2.438 0.333,0.208 10 false * 4.656,2.229 4.99,2.438 0.333,0.208 10 false * 0.146,3.406 1.573,3.635 1.427,0.229 10 false *: Shielded 1.51,0.563 1.927,0.75 0.417,0.188 10 false 6 1.51,1.021 1.927,1.208 0.417,0.188 10 false 2 1.51,1.479 1.927,1.667 0.417,0.188 10 false 3 1.51,1.979 1.927,2.167 0.417,0.188 10 false 5 5.458,0.563 5.698,0.771 0.24,0.208 10 false 11 5.458,1.021 5.688,1.208 0.229,0.188 10 false 24 5.469,1.979 5.719,2.167 0.25,0.188 10 false 23 5.458,1.49 5.719,1.698 0.26,0.208 10 false 12

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the G153 navigation receiver assembly connector.


b.

Disconnect the U6 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G153-11 (CA+) - U6-6 (CB+) Always Below 1 Ω
G153-12 (V+) - U6-3 (CV+) Always Below 1 Ω
G153-24 (V-) - U6-2 (CV-) Always Below 1 Ω
G153-23 (CGND) - U6-5 (CGND) Always Below 1 Ω
G153-11 (CA+) - Body ground Always 10 kΩ or higher
G153-12 (V+) - Body ground Always 10 kΩ or higher
G153-24 (V-) - Body ground Always 10 kΩ or higher
G153-23 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK NAVIGATION RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
E280624
1.458,0.323 2.01,0.583 0.552,0.26 1.094,1.031 0.813,0.729 0.813,0.729 0.469,0.729 true 1.094,1.271 1.021,1.927 1.021,1.927 0.75,1.927 true 0.938,1.271 0.875,1.635 0.875,1.635 0.698,1.635 true 1.552,0.354 2.167,0.552 0.615,0.198 10 false G153 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.469,1.552 0.781,1.75 0.313,0.198 10 false V- 0.135,0.635 0.521,0.833 0.385,0.198 10 false CA+ 0.281,1.844 0.771,2.052 0.49,0.208 10 false CGND
*a Component with harness connected
(Navigation Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G153-23 (CGND) - Body ground Always Below 1 Ω
G153-24 (V-) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G153-11 (CA+) - Body ground Ignition switch ON 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

3.CHECK REAR TELEVISION CAMERA ASSEMBLY

NG

3.CHECK REAR TELEVISION CAMERA ASSEMBLY
a.

Check the waveform of the rear television camera assembly using an oscilloscope.

E280623
1.25,0.531 1.75,0.802 0.5,0.271 3.146,2.292 3.344,2.292 3.344,2.292 3.5,1.792 false 3.885,2.281 3.729,2.281 3.729,2.281 3.594,1.729 false 6.052,2.188 5.896,2.188 5.896,2.188 5.76,1.635 false 5.302,2.177 5.5,2.177 5.5,2.177 5.656,1.677 false 0.646,2.073 0.813,2.073 0.813,2.073 0.917,1.458 true 0.385,0.969 0.552,0.969 0.552,0.969 0.781,1.24 true 0.073,0.167 0.385,0.365 0.313,0.198 10 false *a 3.042,0.188 3.354,0.385 0.313,0.198 10 false *b 5.177,0.167 5.49,0.365 0.313,0.198 10 false *c 2.917,2.188 3.229,2.385 0.313,0.198 10 false *d 5.115,2.094 5.427,2.292 0.313,0.198 10 false *d 3.979,2.198 4.292,2.396 0.313,0.198 10 false *e 6.104,2.104 6.417,2.302 0.313,0.198 10 false *e 4.969,1.354 5.396,1.552 0.427,0.198 10 false GND 2.823,1.344 3.25,1.542 0.427,0.198 10 false GND 0.094,0.906 0.521,1.104 0.427,0.198 10 false V+ 0.188,2.01 0.74,2.229 0.552,0.219 10 false CGND 1.333,0.583 1.76,0.781 0.427,0.198 10 false G153
*a Component with harness connected
(Navigation Receiver Assembly)
*b Waveform 1
*c Waveform 2 *d Synchronized Signal
*e Video Waveform - -


HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.


OK:

Waveform is as shown in the illustration.


Item Content
Terminal No. (Symbol) G153-12 (V+) - G153-23 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Ignition switch ON, camera lens is not covered, displaying an image
Waveform 2: Ignition switch ON, camera lens is covered, blacking out the screen

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.



Result:
Proceed to
OK
NG



OK

NG

REPLACE REAR TELEVISION CAMERA ASSEMBLY