Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2013.11
RM30B0U _56 Audio / Visual / Telematics _009009 NAVIGATION / MULTI INFO DISPLAY _0104226 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Mute Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier  


SYSTEM DESCRIPTION

This circuit sends a signal to the stereo component amplifier assembly to mute noise. Because of that, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E280972
0.75,1.813 1.667,2.01 0.917,0.198 10 false M22 1.781,0.74 1.938,0.938 0.156,0.198 10 false 1 5.313,0.76 5.719,0.958 0.406,0.198 10 false 16 5.573,0.885 6.115,1.115 0.542,0.229 10 false MUT1 1.271,0.875 1.75,1.094 0.479,0.219 10 false MUTE 5.49,1.813 5.979,2.031 0.49,0.219 10 false G143 5.49,1.979 6.802,2.385 1.313,0.406 10 false Navigation Receiver Assembly 0.74,1.969 2.469,2.292 1.729,0.323 10 false Stereo Component Amplifier Assembly

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
E225824
1.49,0.792 1.948,1.073 0.458,0.281 2.396,1.885 2.865,2.385 true 0.208,0.167 0.365,0.333 0.156,0.167 10 false *a 1.594,0.854 2.24,1.021 0.646,0.167 10 false M22 2.698,2.417 3.125,2.583 0.427,0.167 10 false MUTE
*a Component with harness connected
(Stereo Component Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M22-1 (MUTE) - Body ground Ignition switch ACC, audio system playing→ Changing modes Above 3.5 V→ Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the G143 navigation receiver assembly connector.


b.

Disconnect the M22 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-16 (MUT1) - M22-1 (MUTE) Always Below 1 Ω
G143-16 (MUT1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)
a.

Disconnect the navigation receiver assembly connector.


b.
E221772
1.49,0.698 1.948,0.979 0.458,0.281 1.073,2.208 1.323,2.865 true 1.552,0.76 2.042,0.958 0.49,0.198 10 false G143 1.229,2.875 1.906,3.063 0.677,0.188 10 false MUT1 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G143-16 (MUT1) - Body ground Ignition switch ACC, audio system playing→ Changing modes Above 3.5 V→ Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY