Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0046807 ECD SYSTEM(for DPF) J

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST2 of the ignition or starter switch assembly*1 or terminal STAR of the certification ECU (smart key ECU assembly)*2 to the clutch start switch assembly and to terminal STA of the ECM (STA signal).

*1: w/o entry and start system

*2: w/ entry and start system


WIRING DIAGRAM

A284190
0.104,0.083 4.875,0.323 4.771,0.24 12 false w/ Entry and Start System: 0.198,2.646 2.396,3.104 2.198,0.458 10 false Certification ECU (Smart Key ECU Assembly) 0.198,2.458 0.615,2.656 0.417,0.198 10 false G82 5.344,1.052 5.76,1.25 0.417,0.198 10 false A61 5.354,3.771 5.771,3.969 0.417,0.198 10 false A61 4.177,2.25 4.594,2.448 0.417,0.198 10 false A4*1 4.188,2.458 4.604,2.656 0.417,0.198 10 false F2*2 3.917,5.792 4.604,5.958 0.688,0.167 10 false *1: LHD 3.927,6.021 4.615,6.188 0.688,0.167 10 false *2: RHD 4.198,2.698 5.385,3.094 1.188,0.396 10 false Clutch Start Switch Assembly 1.635,6.708 2.135,7.031 0.5,0.323 10 false Starter 0.729,6.792 1.229,7.115 0.5,0.323 10 false Battery 3.271,4.573 3.958,4.74 0.688,0.167 10 false ST 0.583,3.792 1.271,3.958 0.688,0.167 10 false ST 1.365,2.125 1.823,2.323 0.458,0.198 10 false STA 1.365,1.021 1.625,1.24 0.26,0.219 10 false NE 1.281,1.594 1.802,1.813 0.521,0.219 10 false STAR 5.688,1.052 6.24,1.271 0.552,0.219 10 false NEO 5.688,3.656 6.146,3.854 0.458,0.198 10 false STA 5.396,3.552 5.75,3.75 0.354,0.198 10 false 43 1.771,0.917 2.125,1.115 0.354,0.198 10 false 16 5.354,0.844 5.708,1.042 0.354,0.198 10 false 10 1.802,1.479 2.156,1.677 0.354,0.198 10 false 5 1.802,1.99 2.156,2.188 0.354,0.198 10 false 7 2.479,4.104 2.833,4.302 0.354,0.198 10 false 5 2.49,5.052 2.844,5.25 0.354,0.198 10 false 3 3.052,4.115 3.406,4.313 0.354,0.198 10 false 2 3.063,5.052 3.417,5.25 0.354,0.198 10 false 1 6.115,5.031 6.573,5.229 0.458,0.198 10 false ECM 1.76,5.688 2.115,5.896 0.354,0.208 10 false B6 1.063,5.917 1.417,6.125 0.354,0.208 10 false C4 1.563,5.667 1.917,5.865 0.354,0.198 10 false 1 1.083,5.74 1.438,5.938 0.354,0.198 10 false 1 0.563,4.844 1.406,5.052 0.844,0.208 10 false FL MAIN 3.698,2.073 4.052,2.271 0.354,0.198 10 false 2 3.708,2.979 4.063,3.177 0.354,0.198 10 false 1

A284191
4.229,2.323 5.531,2.771 1.302,0.448 10 false Clutch Start Switch Assembly 0.104,0.052 2.302,0.458 2.198,0.406 12 false w/o Entry and Start System: 1.406,1.823 2.604,2.042 1.198,0.219 10 false Ignition Switch 1.583,6.479 2.115,6.844 0.531,0.365 10 false Starter 0.729,6.542 1.26,6.906 0.531,0.365 10 false Battery 3.302,4.344 3.615,4.542 0.313,0.198 10 false ST 1.5,3.229 1.813,3.427 0.313,0.198 10 false ST 0.594,2.198 1.031,2.375 0.438,0.177 10 false AM2 1.25,1.646 1.688,1.823 0.438,0.177 10 false G4 1.521,1.156 1.958,1.333 0.438,0.177 10 false AM2 2.146,1.135 2.583,1.313 0.438,0.177 10 false ST2 1.25,1.135 1.531,1.302 0.281,0.167 10 false 4 2.5,1.135 2.781,1.302 0.281,0.167 10 false 2 1.042,5.698 1.479,5.875 0.438,0.177 10 false C4 1.792,5.469 2.229,5.646 0.438,0.177 10 false B6 1.563,5.458 1.875,5.656 0.313,0.198 10 false 1 1.115,5.531 1.427,5.729 0.313,0.198 10 false 1 2.469,3.885 2.667,4.083 0.198,0.198 10 false 5 2.479,4.823 2.677,5.021 0.198,0.198 10 false 3 3.042,3.875 3.24,4.073 0.198,0.198 10 false 2 3.042,4.844 3.24,5.042 0.198,0.198 10 false 1 5.354,3.552 5.667,3.75 0.313,0.198 10 false A61 5.375,3.354 5.688,3.552 0.313,0.198 10 false 43 5.698,3.438 6.01,3.635 0.313,0.198 10 false STA 6.094,4.802 6.781,5.063 0.688,0.26 10 false ECM 4.198,1.792 4.625,2.01 0.427,0.219 10 false A4*1 4.208,2 4.635,2.219 0.427,0.219 10 false F2*2 3.969,5.5 4.5,5.677 0.531,0.177 10 false *1: LHD 3.99,5.76 4.521,5.938 0.531,0.177 10 false *2: RHD 0.573,4.729 1.406,4.958 0.833,0.229 10 false FL MAIN 3.76,1.802 3.958,2 0.198,0.198 10 false 2 3.792,2.802 3.99,3 0.198,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·


PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.

Result:
Proceed to
Engine cannot be cranked
Engine can be cranked




Engine cannot be cranked

2.READ VALUE USING GTS (STARTER SIGNAL)

Engine can be cranked

16.READ VALUE USING GTS (STARTER SIGNAL)
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 61 193

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Switch Position Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

3.INSPECT ST RELAY

NG

10.INSPECT CLUTCH START SWITCH ASSEMBLY
3.INSPECT ST RELAY

Result:
Proceed to
OK
NG



OK

4.INSPECT STARTER ASSEMBLY

NG

REPLACE ST RELAY

4.INSPECT STARTER ASSEMBLY
a.

Inspect the starter assembly.

Click hereEngine / Hybrid System>2AD-FTV STARTING>STARTER>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)

NG

REPLACE STARTER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)
a.

Remove the ST relay from the engine room relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ST relay) - B6-1 Always Below 1 Ω
3 (ST relay) or B6-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STARTER ASSEMBLY)
a.

Disconnect the starter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C4-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)
a.
A296486
0.094,0.146 0.406,0.302 0.313,0.156 10 *1 2.073,3.51 2.385,3.667 0.313,0.156 10 *2
*1 Engine Room NO. 2 Relay Block and Junction Block Assembly
*2 ST Relay


Remove the ST relay from the engine room NO. 2 relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST RELAY)

8.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.

Remove the ST relay from the engine room NO. 2 relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (ST RELAY - CLUTCH START SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (ST RELAY - CLUTCH START SWITCH ASSEMBLY)
a.

Remove the ST relay from the engine room NO. 2 relay block and junction block assembly.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST relay) - A4-1*1 Always Below 1 Ω
2 (ST relay) - F2-1*2 Always Below 1 Ω


·

*1: LHD

·

*2: RHD



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly (Click here Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION).


Result:
Proceed to
OK (w/ entry and start system)
OK (w/o entry and start system)
NG



OK (w/ entry and start system)

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)

OK (w/o entry and start system)

13.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-5 (STAR) - A4-2*1 Always Below 1 Ω
G82-5 (STAR) - F2-2*2 Always Below 1 Ω
G82-5 (STAR) or A4-2*1 - Body ground Always 10 kΩ or higher
G82-5 (STAR) or F2-2*2 - Body ground Always 10 kΩ or higher


·

*1: LHD

·

*2: RHD



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM)
a.

Disconnect the clutch start switch assembly connector.


b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-1*1 - A61-43 (STA) Always Below 1 Ω
F2-1*2 - A61-43 (STA) Always Below 1 Ω
A4-1*1 or A61-43 (STA) - Body ground Always 10 kΩ or higher
F2-1*2 or A61-43 (STA) - Body ground Always 10 kΩ or higher


·

*1: LHD

·

*2: RHD



Result:
Proceed to
OK
NG



OK

GO TO ENTRY AND START SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2AD-FTV STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

14.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-2 (ST2) - A4-2*1 Always Below 1 Ω
G4-2 (ST2) - F2-2*2 Always Below 1 Ω
G4-2 (ST2) or A4-2*1 - Body ground Always 10 kΩ or higher
G4-2 (ST2) or F2-2*2 - Body ground Always 10 kΩ or higher


·

*1: LHD

·

*2: RHD



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM)
a.

Disconnect the clutch start switch assembly connector.


b.

Remove the ST relay from the engine room NO. 2 relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-1*1 - A61-43 (STA) Always Below 1 Ω
F2-1*2 - A61-43 (STA) Always Below 1 Ω
A4-1*1 or A61-43 (STA) - Body ground Always 10 kΩ or higher
F2-1*2 or A61-43 (STA) - Body ground Always 10 kΩ or higher


·

*1: LHD

·

*2: RHD



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 61 193

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Switch Position Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - ECM)