Refer to DTC P0087 (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P0087).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0191 | Fuel Rail Pressure Sensor Circuit Range / Performance | The difference between the main and sub voltage outputs of the fuel pressure sensor is 0.04 V or less, or 1.06 V or higher for 1 second or more.
(1 trip detection logic) |
·
Open or short in fuel pressure sensor circuit ·
Fuel pressure sensor (common rail assembly) ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0191 | ·
Fuel Press ·
Target Common Rail Pressure |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0191 | Idling for 1 second |
Refer to DTC P0087 (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P0087).
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.
| Tester Display |
|---|
| Target Common Rail Pressure |
| Fuel Press |
Start the engine.
Check the change in the values for the Data List items above when increasing the engine speed from idling to 3000 rpm with no load.
| Result | Proceed to |
|---|---|
| Fuel Press is always 10000 kPa or less
or Fuel Press is always 200000 kPa or higher |
A |
| Except above | B |
Normally, "Fuel Press" is +/-5000 kPa of "Target Common Rail Pressure".
A
B
Disconnect the fuel pressure sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B70-5 (PR) - B76-66 (PCR1) | Always | Below 1 Ω |
| B70-2 (PR2) - B76-114 (PCR2) | Always | Below 1 Ω |
| B70-1 (VCS) - B76-69 (VCS) | Always | Below 1 Ω |
| B70-6 (VC) - B76-68 (VCM) | Always | Below 1 Ω |
| B70-4 (E2) - B76-67 (E2M) | Always | Below 1 Ω |
| B70-3 (E2S) - B76-91 (E2S) | Always | Below 1 Ω |
| B70-5 (PR) or B76-66 (PCR1) - Body ground | Always | 10 kΩ or higher |
| B70-2 (PR2) or B76-114 (PCR2) - Body ground | Always | 10 kΩ or higher |
| B70-1 (VCS) or B76-69 (VCS) - Body ground | Always | 10 kΩ or higher |
| B70-6 (VC) or B76-68 (VCM) - Body ground | Always | 10 kΩ or higher |
| B70-4 (E2) or B76-67 (E2M) - Body ground | Always | 10 kΩ or higher |
| B70-3 (E2S) or B76-91 (E2S) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Let the engine idle for 1 second.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Proceed to |
|---|
| DTC P0191 is output |
| DTC is not output |
DTC P0191 is output
DTC is not output
Replace the common rail assembly.
Click hereEngine / Hybrid System>2AD-FTV FUEL>COMMON RAIL>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Let the engine idle for 1 second.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Proceed to |
|---|
| DTC P0191 is output |
| DTC is not output |
DTC P0191 is output
DTC is not output
Replace the ECM.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Let the engine idle for 1 second.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT