Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0046807 ECD SYSTEM(for DPF) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P2121  Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance  


DESCRIPTION

Refer to DTC P2120 (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P2120).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance The difference between VPA and VPA2 is below 0.4 V, or higher than 1.2 V for 0.5 seconds.
(1 trip detection logic)
·

Accelerator pedal position sensor circuit

·

Accelerator pedal position sensor

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2121
·

Accel Position

·

Accel Sens. No.1 Volt %

·

Accel Sens. No.2 Volt %



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2121 Ignition switch ON
·

Accelerator pedal fully closed for 3 seconds

·

Accelerator pedal open partway for 3 seconds

·

Accelerator pedal fully open for 3 seconds



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

Powertrain > Engine > Data List
Tester Display
Accel Sens. No.1 Volt %
Accel Sens. No.2 Volt %
50003 61 75,76

d.

Read the values.

Standard Voltage:
Accelerator Pedal Accel Sens. No.1 Volt % Accel Sens. No.2 Volt %
Released 10 to 22% 24 to 40%
Depressed 52 to 90% 68 to 95%



Result:
Proceed to
OK
NG



NG

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

OK

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-1 (VCP2) - A61-57 (VCP2) Always Below 1 Ω
A6-2 (EPA2) - A61-58 (EPA2) Always Below 1 Ω
A6-3 (VPA2) - A61-54 (VPA2) Always Below 1 Ω
A6-4 (VCPA) - A61-55 (VCPA) Always Below 1 Ω
A6-5 (EPA) - A61-56 (EPA) Always Below 1 Ω
A6-6 (VPA) - A61-53 (VPA) Always Below 1 Ω
A6-1 (VCP2) or A61-57 (VCP2) - Body ground Always 10 kΩ or higher
A6-2 (EPA2) or A61-58 (EPA2) - Body ground Always 10 kΩ or higher
A6-3 (VPA2) or A61-54 (VPA2) - Body ground Always 10 kΩ or higher
A6-4 (VCPA) or A61-55 (VCPA) - Body ground Always 10 kΩ or higher
A6-5 (EPA) or A61-56 (EPA) - Body ground Always 10 kΩ or higher
A6-6 (VPA) or A61-53 (VPA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch to ON.


f.

Fully close the accelerator pedal for 3 seconds or more, then hold it partway open for 3 seconds or more, and then fully open it for 3 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

h.

Read the DTCs.

Result:
Proceed to
DTC P2121 is output
DTC is not output




DTC P2121 is output

5.REPLACE ECM

DTC is not output

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch to ON.


f.

Fully close the accelerator pedal for 3 seconds or more, then hold it partway open for 3 seconds or more, and then fully open it for 3 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END