Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0046807 ECD SYSTEM(for DPF) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0088  Fuel Rail / System Pressure - Too High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0088 Fuel Rail / System Pressure - Too High The fuel pressure of the common rail exceeds 220000 kPa (2243.4 kgf/cm2, 31900 psi).
(1 trip detection logic)
·

Supply pump assembly (suction control valve)

·

Pressure discharge valve (built into common rail assembly)

·

Open or short in supply pump assembly (suction control valve) circuit

·

Fuel pressure sensor (built into common rail assembly)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0088
·

Fuel Press

·

Target Common Rail Pressure

·

Injection Pressure Correction

·

Target Pump SCV Current

·

Pressure Discharge Valve



HINT:
·

For more information on the fuel supply pump (suction control valve) and common rail system, refer to System Description (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).

·

When DTC P0088 is stored, check the internal fuel pressure of the common rail by entering the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

Reference
Engine Speed Fuel Press
Idling Approximately 27000 to 45000 kPa
3000 rpm (No engine load) Approximately 45000 to 78000 kPa

·

When there is an operating problem with the fuel supply pump (when Fuel Press is more than Target Common Rail Pressure due to a problem with the closing of the suction valve), the values of Injection Pressure Correction and Target Pump SCV Current decrease.

·

Check "Fuel Press", "Target Common Rail Pressure", "Target Pump SCV Current" and "Pressure Discharge Valve" in the freeze frame data.



MONITOR DESCRIPTION

P0088 (Internal fuel pressure too high):

The ECM stores this DTC if the fuel pressure inside the common rail is more than 220000 kPa (2243 kgf/cm2, 31900 psi). This DTC indicates that: 1) the suction control valve may be stuck open, or 2) there may be a short in the suction control valve circuit.

If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The fail-safe mode continues until the ignition switch is turned off.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0088 After idling for 60 seconds, repeat quick engine speed accelerations (from idling to 2500 rpm) for 30 seconds

WIRING DIAGRAM

A205135E01
2.063,1.396 2.26,1.573 0.198,0.177 10 2 5.427,0.698 5.698,0.875 0.271,0.177 10 41 5.427,1.375 5.698,1.552 0.271,0.177 10 81 5.708,1.281 6.125,1.458 0.417,0.177 10 PCV- 5.99,2.021 6.385,2.198 0.396,0.177 10 ECM 5.708,0.625 6.125,0.802 0.417,0.177 10 PCV+ 2.073,0.729 2.271,0.906 0.198,0.177 10 1 0.646,2.031 2.042,2.219 1.396,0.188 10 Suction Control Valve 5.99,1.833 6.26,1.99 0.271,0.156 10 B76 0.667,1.854 0.969,2.031 0.302,0.177 10 B48

CAUTION / NOTICE / HINT

NOTICE:
·
·

After replacing the fuel supply pump, the ECM needs initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0088)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read Current DTCs.

Result:
Proceed to
DTC P0088 is output
DTC P0088 and other DTCs are output


HINT:

If any DTCs other than P0088 are output, troubleshoot those DTCs first.




DTC P0088 is output

2.CHECK FREEZE FRAME DATA (FUEL PRESS)

DTC P0088 and other DTCs are output

2.CHECK FREEZE FRAME DATA (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Record the stored DTC and freeze frame data.

Result:
Result Proceed to
Except below A
Value of Fuel Press is shifting towards 160000 kPa or higher in 3rd and 4th set of freeze frame data B




A

3.CHECK HARNESS AND CONNECTOR

B

4.REPLACE SUCTION CONTROL VALVE
3.CHECK HARNESS AND CONNECTOR
HINT:

If the MIL has illuminated before in the past, clear the DTC using the GTS before performing this inspection.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR


A194532C01
0.75,2.188 0.354,2.469 0.354,2.469 0.354,2.677 false 1.292,1.323 1.625,3.24 1.625,3.24 1.813,3.24 true 1.542,0.344 1.854,0.5 0.313,0.156 10 *1 0.292,2.719 0.604,2.875 0.313,0.156 10 *2 1.854,3.177 2.167,3.333 0.313,0.156 10 *3 3.729,1.135 4.042,1.292 0.313,0.156 10 *4 5.833,1.104 6.146,1.26 0.313,0.156 10 *5 0.125,0.104 0.438,0.26 0.313,0.156 10 *a
*1 Engine *2 Engine Wire
*3 Common Rail Assembly
(Fuel Pressure Sensor)
*4 Wire to Wire
*5 ECM - -
*a Vibration Method (Reference) - -


Result:
Proceed to
MIL does not come on
MIL comes on



MIL does not come on

4.REPLACE SUCTION CONTROL VALVE

MIL comes on

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE SUCTION CONTROL VALVE
a.

Replace the suction control valve.

Click hereEngine / Hybrid System>2AD-FTV FUEL>SUCTION CONTROL VALVE>REMOVAL

HINT:

Before replacing the supply pump assembly, check that the wire harness between the suction control valve and ECM is not shorted to ground.

When there is a malfunction in the wire harness, Target Pump SCV Current is outside the range of 923 to 1123 mA when idling, and outside the range of 1013 to 1212 mA when the engine is running at 2500 rpm without load.

If there are no problems with the engine condition during idling, it is not necessary to perform the above wire harness inspection.

When the wire harness between the suction control valve and ECM is not shorted to ground, it can be assumed that DTC P0088 was stored due to a malfunction in the operation of the suction control valve. Therefore, it is necessary to replace the supply pump assembly.



Result:
Proceed to
NEXT



NEXT

5.BLEED AIR FROM FUEL SYSTEM
5.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

6.PERFORM SUPPLY PUMP INITIALIZATION
6.PERFORM SUPPLY PUMP INITIALIZATION

Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for 30 seconds or more.


f.

Start the engine and turn the GTS on.


g.

After idling for 60 seconds, repeat quick engine speed accelerations (from idling to 2500 rpm) for 30 seconds.


h.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0088.


iii.

Check the DTC judgment result.

Result:
GTS Display Result Proceed to
Pending DTC DTC P0088 is output A
All Readiness NORMAL B
ABNORMAL A


HINT:

If STATUS is INCOMPLETE or N/A, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.





A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CHECK HARNESS AND CONNECTOR
10.CHECK HARNESS AND CONNECTOR
HINT:

If the MIL has illuminated before in the past, clear the DTC using the GTS before performing this inspection.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR


A194532C01
0.75,2.188 0.354,2.469 0.354,2.469 0.354,2.677 false 1.292,1.323 1.625,3.24 1.625,3.24 1.813,3.24 true 1.542,0.344 1.854,0.5 0.313,0.156 10 *1 0.292,2.719 0.604,2.875 0.313,0.156 10 *2 1.854,3.177 2.167,3.333 0.313,0.156 10 *3 3.729,1.135 4.042,1.292 0.313,0.156 10 *4 5.833,1.104 6.146,1.26 0.313,0.156 10 *5 0.125,0.104 0.438,0.26 0.313,0.156 10 *a
*1 Engine *2 Engine Wire
*3 Common Rail Assembly
(Fuel Pressure Sensor)
*4 Wire to Wire
*5 ECM - -
*a Vibration Method (Reference) - -


Result:
Proceed to
MIL does not come on
MIL comes on



MIL comes on

11.REPLACE COMMON RAIL ASSEMBLY

MIL does not come on

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>2AD-FTV FUEL>COMMON RAIL>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.BLEED AIR FROM FUEL SYSTEM
12.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for 30 seconds or more.


f.

Start the engine and turn the GTS on.


g.

After idling for 60 seconds, repeat quick engine speed accelerations (from idling to 2500 rpm) for 30 seconds.


h.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0088.


iii.

Check that STATUS is NORMAL.

HINT:

If STATUS is INCOMPLETE or N/A, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.




Result:
Proceed to
NEXT



NEXT

END