Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0046807 ECD SYSTEM(for DPF) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P1271  Fuel Regulator Circuit Malfunction (EDU Drive)  P1272  Fuel Pressure Regulator Malfunction  


DESCRIPTION

The ECM controls the internal fuel pressure of the common rail by opening and closing the pressure discharge valve. When sudden deceleration occurs, the internal fuel pressure will temporarily become higher than usual and combustion noise may result. Therefore the ECM will open the valve temporarily to discharge the excess pressure inside the common rail. Also, the pressure discharge valve opens when the ignition switch is turned off to allow prompt discharge of the common rail internal pressure and so that the engine stops smoothly.

HINT:
·

For more information on the pressure discharge valve and common rail system (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).

·

If P1271 and/or P1272 is present, refer to the DTC chart for the fuel system (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).



A208468E01
0.057,0.035 3.921,0.212 3.865,0.177 10 Pressure Discharge Valve Operation by Sudden Deceleration: 0.928,0.378 2.056,0.722 1.128,0.344 10 Accelerator Pedal Opening Angle 0.403,1.389 2.038,1.552 1.635,0.163 10 Pressure Discharge Valve 1.132,2.292 2.045,2.455 0.913,0.163 10 Fuel Pressure 2.595,0.546 2.98,0.709 0.385,0.163 10 Open 4.139,1.391 4.525,1.554 0.385,0.163 10 Open 2.595,1.156 3.077,1.319 0.483,0.163 10 Closed 4.139,0.722 4.659,0.885 0.52,0.163 10 Closed 4.22,2.134 6.133,2.276 1.913,0.142 10 w/o Pressure Discharge Valve 1.673,2.706 3.482,2.848 1.809,0.142 10 w/ Pressure Discharge Valve 2.079,3.063 3.43,3.226 1.351,0.163 10 Target Fuel Pressure 3.932,3.287 4.942,3.45 1.01,0.163 10 Time Reduction 3.323,3.528 3.674,3.677 0.351,0.149 10 Time 3.73,2.783 3.499,2.783 false 3.685,3.0 3.495,3.14 3.495,3.14 3.415,3.14 false 3.898,2.424 4.087,2.224 4.087,2.224 4.183,2.224 false

A205138E01
6.795,2.675 7.136,2.779 0.341,0.105 0.042,0.073 3.564,0.248 3.522,0.175 10 Cross Section Diagram of Pressure Discharge Valve: 0.538,1.648 1.764,1.998 1.226,0.351 10 From Common Rail (High Pressure) 1.877,0.475 4.355,0.663 2.478,0.189 10 Return to Fuel Tank (Low Pressure) 3.044,2.426 3.413,2.596 0.369,0.17 10 Valve 5.299,1.685 5.882,1.856 0.582,0.17 10 Solenoid 3.448,1.802 2.859,2.5 2.859,2.5 2.977,2.5 false 4.252,2.12 5.1,1.764 5.1,1.764 5.254,1.764 false

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1271 Fuel Regulator Circuit Malfunction (EDU Drive) When either condition below is met (1 trip detection logic):
·

Open or short in pressure discharge valve circuit.

·

There is no valve opening confirmation (IJf) signal from the EDU to the ECM for a specific number of times consecutively, despite the ECM sending valve opening command (PRD) signals after the engine is started


·

Open or short in pressure discharge valve circuit

·

Pressure discharge valve (built into common rail assembly)

·

Injector driver (EDU)


Comes on DTC stored
P1272 Fuel Pressure Regulator Malfunction Pressure discharge valve does not open.
Actual pressure decreasing rate deviates from the simulated pressure decreasing rate after the ignition switch is turned off.
(2 trip detection logic)
·

Open or short in pressure discharge valve circuit (P1271 is set simultaneously)

·

Pressure discharge valve (built into common rail assembly)

·

Injector driver (EDU)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P1271
·

Fuel Press

·

Target Common Rail Pressure

·

Pressure Discharge Valve


P1272

HINT:
·

After confirming DTC P1271 and/or P1272, check the fuel pressure inside the common rail in "Powertrain / Engine and ECT / Data List / Fuel Press" using the GTS.

·

P1271:

After clearing the DTC, drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal. Check that P1271 is not stored.

·

P1272:

After clearing the DTC, start and stop the engine twice (wait 30 seconds or more after turning the ignition switch off before starting the engine the second time), and then confirm that P1272 is not stored.


Reference:
Engine Speed Fuel Pressure (kPa)
Idling Fuel Press is within +/-5000 kPa of Target Common Rail Pressure
2500 rpm (No engine load)

Results of real-vehicle check:
Condition Fuel Press (Idling) Fuel Press (1 Second after Engine Stopped)
Pressure discharge valve normal 35000 kPa 170 kPa
Open in pressure discharge valve circuit 34000 kPa 34300 kPa


MONITOR DESCRIPTION

P1271 (Open or short in pressure discharge valve circuit):

This DTC will be set if there is no valve opening confirmation (IJf) signal sent from the injector driver (EDU) to the ECM, despite the ECM has commanded the injector driver (EDU) to open the pressure discharge valve. This DTC refers to an open or short circuit malfunction of the pressure discharge valve circuit, not a malfunction in which a valve is stuck open or closed.

The injector driver (EDU) monitors the current supplied to the pressure discharge valve to verify that the current flows into the valve. If the current exceeds the specified level, the injector driver (EDU) interprets this as the IJf signal being low. If this DTC is stored, the ECM enters the fail-safe mode and limits engine power. The fail-safe mode continues until the ignition switch is turned off.

A208469E01
0.112,0.053 1.442,0.21 1.33,0.157 10 P1271 Malfunction: 0.164,1.86 1.82,2.225 1.656,0.365 10 Pressure Discharge Valve Command Signal 1.933,1.958 2.312,2.142 0.378,0.184 10 PRD 2.358,0.852 2.736,1.036 0.378,0.184 10 ECM 5.762,0.857 6.14,1.041 0.378,0.184 10 EDU 2.818,1.413 3.085,1.597 0.267,0.184 10 On 3.295,1.717 3.546,1.901 0.25,0.184 10 Off 4.182,2.412 4.955,2.596 0.773,0.184 10 Abnormal 3.12,3.286 3.653,3.47 0.533,0.184 10 Normal 0.164,2.589 1.82,2.953 1.656,0.365 10 Pressure Discharge Valve Confirmation Signal 1.968,2.687 2.326,2.871 0.358,0.184 10 IJf-R 3.313,1.164 4.856,1.349 1.543,0.184 10 Confirmation Signal (IJf) 3.313,0.455 5.273,0.639 1.959,0.184 10 Command Signal (PRD) 3.863,2.752 3.982,2.487 3.982,2.487 4.137,2.487 false 3.856,3.092 3.779,3.37 3.779,3.37 3.646,3.37 false


P1272 (Closed malfunction of the pressure discharge valve):

The pressure discharge valve will open and discharge the internal fuel pressure from the common rail to the fuel tank when the ignition switch is turned off. In this event, the ECM compares the actual drop rate of the internal fuel pressure and the target drop rate. If the ECM judges that the actual drop rate is smaller than the target, the ECM then judges that the valve is stuck closed and stores this DTC. This DTC will be stored if the internal fuel pressure does not drop to the target after the ignition switch has been turned off.

If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The fail-safe mode continues until the ignition switch is turned off.


MONITOR STRATEGY

P1271:
Required sensors EDU
Frequency of operation Continuous
Duration 3 seconds
MIL operation 1 driving cycle

P1272:
Required sensors Fuel pressure sensor
Frequency of operation Once per driving cycle
Duration 1 second
MIL operation 2 driving cycles

TYPICAL ENABLING CONDITIONS

P1271:
Specification
The vehicle is driven at 50 km/h (31 mph) in 3rd gear, and then decelerated by complete release of the accelerator pedal 3 times.

P1272:
Item Specification
Minimum Maximum
Fuel pressure 30000 kPa (306 kgf/cm2, 4350 psi) -
Fuel temperature 0°C (32°F) -
Battery voltage 11 V -
The monitor will not run if the fuel pressure sensor, pressure discharge valve circuit or fuel temperature sensor is malfunctioning.

TYPICAL MALFUNCTION THRESHOLDS

P1271:
Specification
There are no confirmation signals from the injector driver (EDU) for a specific number of times consecutively, despite the ECM sending command signals regularly during deceleration.

P1272:
Specification
The internal pressure stays beyond the specified level after the ignition switch is turned off.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P1271 Ignition switch ON to off
and
Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal
P1272 Ignition switch ON to off

WIRING DIAGRAM

A210269E04
0.281,3.073 1.906,3.281 1.625,0.208 10 Injector Driver (EDU) 1.385,0.24 1.49,0.406 0.104,0.167 10 5 1.271,2.698 1.552,2.854 0.281,0.156 10 B54 5.979,3.167 6.313,3.333 0.333,0.167 10 ECM 5.5,0.365 5.677,0.531 0.177,0.167 10 52 5.979,3.042 6.26,3.198 0.281,0.156 10 B76 5.781,0.438 6.125,0.594 0.344,0.156 10 PRD 0.917,1.125 1.229,1.281 0.313,0.156 10 RLF 1.281,1.135 1.563,1.292 0.281,0.156 10 B53 0.844,2.688 1.229,2.844 0.385,0.156 10 RLF- 0.833,1.844 1.229,2 0.396,0.156 10 RLF+ 3.583,2.125 3.927,2.281 0.344,0.156 10 B69 3.583,2.271 5.219,2.427 1.635,0.156 10 Pressure Discharge Valve 4.677,1.938 4.792,2.094 0.115,0.156 10 2 3.938,1.948 4.052,2.104 0.115,0.156 10 1 5.781,1.125 6.188,1.292 0.406,0.167 10 RLFF 5.438,1.021 5.708,1.188 0.271,0.167 10 123 1.281,1.875 1.563,2.031 0.281,0.156 10 B54 1.281,0.479 1.563,0.635 0.281,0.156 10 B53 1.354,0.906 1.5,1.073 0.146,0.167 10 1 0.885,0.448 1.229,0.604 0.344,0.156 10 PRD 1.365,1.646 1.469,1.833 0.104,0.188 10 1 1.375,2.479 1.51,2.646 0.135,0.167 10 2

Refer to DTC P0201 (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P0201).

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).


HINT:
·

After completing repairs, confirm that P1271 and/or P1272 does not recur.

·

If P062D and P1271 are present simultaneously, there is an open in the INJF wire harness between the injector driver (EDU) and ECM, or there is an open in the wire harness for both an injector and the pressure discharge valve.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK IF DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON.


g.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

i.

Read the pending DTCs.

Result:
Result Proceed to
DTC P1272 is output A
DTC P1271 is output B
DTC P1271 and P1272 are output
Other DTCs are output C




A

2.CHECK COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE OPERATION)

B

3.INSPECT PRESSURE DISCHARGE VALVE

C

2.CHECK COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE OPERATION)
a.

Inspect the common rail assembly.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

12.REPLACE COMMON RAIL ASSEMBLY
3.INSPECT PRESSURE DISCHARGE VALVE
a.

Inspect the pressure discharge valve.

Click hereEngine / Hybrid System>2AD-FTV FUEL>COMMON RAIL>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - INJECTOR DRIVER (EDU))

NG

12.REPLACE COMMON RAIL ASSEMBLY
4.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - INJECTOR DRIVER (EDU))
a.

Disconnect the pressure discharge valve connector.


b.

Disconnect the injector driver (EDU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B69-1 - B54-1 (RLF+) Always Below 1 Ω
B69-2 - B54-2 (RLF-) Always Below 1 Ω
B69-1 or B54-1 (RLF+) - Body ground Always 10 kΩ or higher
B69-2 or B54-2 (RLF-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER (EDU) - ECM)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER (EDU) - ECM)
a.

Disconnect the injector driver (EDU) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B53-5 (PRD) - B76-52 (PRD) Always Below 1 Ω
B53-1 (RLF) - B76-123 (RLFF) Always Below 1 Ω
B53-5 (PRD) or B76-52 (PRD) - Body ground Always 10 kΩ or higher
B53-1 (RLF) or B76-123 (RLFF) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF INJECTOR DRIVER (EDU))

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF INJECTOR DRIVER (EDU))
a.
A204910C02
0.49,1.021 0.896,1.281 0.406,0.26 1.958,0.958 2.458,0.698 true 1.948,1.406 2.354,1.615 true 2.521,0.604 2.813,0.823 0.292,0.219 10 +B 2.406,1.573 2.792,1.792 0.385,0.219 10 GND 0.229,0.208 0.406,0.365 0.177,0.156 10 *a 0.552,1.063 0.854,1.229 0.302,0.167 10 B51
*a Front view of wire harness connector
(to Injector Driver (EDU))


Disconnect the injector driver (EDU) connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B51-2 (+B) - B51-4 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.REPLACE INJECTOR DRIVER (EDU)

NG

10.GO TO INJECTOR CIRCUIT
7.REPLACE INJECTOR DRIVER (EDU)
a.

Replace the injector driver (EDU).

Click hereEngine / Hybrid System>2AD-FTV FUEL>INJECTOR DRIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK IF DTC OUTPUT RECURS (DTC P1271 AND/OR P1272)
8.CHECK IF DTC OUTPUT RECURS (DTC P1271 AND/OR P1272)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON.


g.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

i.

Read the pending DTCs.

HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P1271 and P1272.


iii.

Check the DTC judgment result.

Result:
GTS Display Result Proceed to
Pending DTC DTC P1271 and/or P1272 is output B
All Readiness NORMAL A
ABNORMAL B


HINT:

If STATUS is INCOMPLETE or N/A, perform the following procedure 3 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.





A

END

B

9.REPLACE ECM
9.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.GO TO INJECTOR CIRCUIT

Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>2AD-FTV FUEL>COMMON RAIL>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.BLEED AIR FROM FUEL SYSTEM
13.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON.


g.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

i.

Confirm that the pending DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P1271 and P1272.


iii.

Check the DTC judgment result.

HINT:

If STATUS is INCOMPLETE or N/A, perform the following procedure 3 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.




Result:
Proceed to
NEXT



NEXT

END