Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0046807 ECD SYSTEM(for DPF) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0545  Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 1)  P0546  Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 1)  P2032  Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 2)  P2033  Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 2)  


DESCRIPTION

A208466
5.865,4.865 6.052,4.865 false 1.615,5.615 1.729,5.615 false 1.219,2.688 0.656,2.896 false 2.188,3.219 2.417,3.49 false 2.219,2.219 2.396,0.052 2.396,0.052 2.313,0.052 false 0.167,0 2.292,0.313 2.125,0.313 10 false Exhaust Gas Temperature Sensor (B1S1) 1.281,0.885 2.125,1.063 0.844,0.177 10 false Exhaust Gas 2.948,1.344 3.313,1.51 0.365,0.167 10 false ECM 0.073,2.938 1.063,3.271 0.99,0.333 10 false DPF Catalytic Converter 2.458,3.438 4.823,3.854 2.365,0.417 10 false NO. 2 Exhaust Gas Temperature Sensor (B1S2) 4.208,0.677 6.688,1.031 2.479,0.354 10 false Cross Section Diagram of Exhaust Gas Temperature Sensor: 0.094,3.99 1.833,4.177 1.74,0.188 10 false Property of Output Voltage: 1.49,4.323 3.156,4.521 1.667,0.198 10 false Exhaust Gas Temperature 3.271,4.323 3.781,4.5 0.51,0.177 10 false °C (°F) 0.625,4.458 1.427,4.625 0.802,0.167 10 false 1000 (1832) 0.698,4.625 1.396,4.792 0.698,0.167 10 false 960 (1760) 0.698,4.854 1.396,5.021 0.698,0.167 10 false 760 (1400) 0.698,5.125 1.396,5.292 0.698,0.167 10 false 560 (1040) 0.771,5.365 1.396,5.531 0.625,0.167 10 false 360 (680) 0.76,5.615 1.396,5.781 0.635,0.167 10 false 160 (320) 0.813,5.917 1.396,6.083 0.583,0.167 10 false -40 (-40) 1.417,6.042 1.521,6.229 0.104,0.188 10 false 0 1.563,6.052 1.781,6.24 0.219,0.188 10 false 0.2 1.865,6.042 2.104,6.229 0.24,0.188 10 false 0.5 2.323,6.042 2.563,6.229 0.24,0.188 10 false 1.0 2.792,6.042 3.031,6.229 0.24,0.188 10 false 1.5 3.26,6.042 3.5,6.229 0.24,0.188 10 false 2.0 3.729,6.042 3.969,6.229 0.24,0.188 10 false 2.5 4.198,6.042 4.438,6.229 0.24,0.188 10 false 3.0 4.646,6.042 4.854,6.229 0.208,0.188 10 false 3.5 5.115,6.042 5.323,6.229 0.208,0.188 10 false 4.0 5.583,6.042 5.802,6.229 0.219,0.188 10 false 4.5 5.823,6.042 6.135,6.229 0.313,0.188 10 false 4.95 6.115,6.042 6.344,6.229 0.229,0.188 10 false 5.0 2.49,6.292 5.365,6.5 2.875,0.208 10 false Exhaust Gas Temperature Sensor Voltage (V) 1.771,5.552 3.271,5.708 1.5,0.156 10 false Stores P0545 or P2032 4.375,4.792 5.875,4.948 1.5,0.156 10 false Stores P0546 or P2033

The exhaust gas temperature sensors are installed before and after the Diesel Particulate Filter (DPF) catalytic converter to sense the exhaust gas temperature.

A thermistor built into the sensor changes its resistance value according to the exhaust gas temperature. The lower the exhaust gas temperature, the higher the thermistor resistance value. The higher the exhaust gas temperature, the lower the thermistor resistance value.

The exhaust gas temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the exhaust gas temperature sensor from terminal THCI (B1S1) and THCO (B1S2) via resistor R.

Resistor R and the exhaust gas temperature sensor are connected in series. When the resistance value of the exhaust gas temperature sensor changes in accordance with the exhaust gas temperature, the voltage at terminals THCI (B1S1) and THCO (B1S2) also changes. When PM forced regeneration is needed, the ECM operates the exhaust fuel addition injector to obtain target upstream temperature of the DPF catalytic converter as monitored through sensor 1. In addition, the ECM monitors the temperature increase of the DPF catalytic converter using sensor 2.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0545 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 1) Exhaust gas temperature sensor (B1S1) output voltage is below 0.2 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or higher


·

Open or short in exhaust gas temperature sensor (B1S1) circuit

·

Exhaust gas temperature sensor (B1S1)

·

ECM


Comes on DTC stored
P0546 Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 1) Exhaust gas temperature sensor (B1S1) output voltage is higher than 4.95 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or higher


·

Open or short in exhaust gas temperature sensor (B1S1) circuit

·

Exhaust gas temperature sensor (B1S1)

·

ECM


Comes on DTC stored
P2032 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 2) No. 2 exhaust gas temperature sensor (B1S2) output voltage is below 0.2 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or higher


·

Open or short in No. 2 exhaust gas temperature sensor (B1S2) circuit

·

No. 2 exhaust gas temperature sensor (B1S2)

·

ECM


Comes on DTC stored
P2033 Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 2) No. 2 exhaust gas temperature sensor (B1S2) output voltage is higher than 4.95 V for 3 seconds or more when all conditions are met.(1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or higher


·

Open or short in No. 2 exhaust gas temperature sensor (B1S2) circuit

·

No. 2 exhaust gas temperature sensor (B1S2)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0545 Exhaust Temperature B1S1
P0546
P2032 Exhaust Temperature B1S2
P2033

HINT:
·

DTC P1386 (Exhaust fuel addition injector malfunction) may be stored if there is an open malfunction in an exhaust gas temperature sensor circuit.

·

Sensor 1 the represents sensor located upstream in front of the DPF catalytic converter.

·

Sensor 2 the represents sensor located downstream behind the DPF catalytic converter.

·

After confirming DTC P0545, P0546, P2032, and/or P2033, check the upstream and downstream exhaust gas temperature in "Powertrain / Engine and ECT / Exhaust Temperature B1S1 and Exhaust Temperature B1S2" using the GTS.


Reference:
Condition Exhaust Gas Temperature Exhaust Gas Temperature Sensor Condition
Idling after warm-up Constant at between 50 and 700°C (122 and 1292°F) Normal
0°C (32°F) Open circuit
1000°C (1832°F) Short circuit


MONITOR DESCRIPTION

The ECM constantly monitors the output voltages from the exhaust gas temperature sensors in order to detect problems with the sensors. When the sensor output voltage deviates from the normal operating range (between 0.2 V and 4.95 V) for more than 3 seconds after the engine is warmed up, the ECM interprets this as malfunction of the sensor circuit and illuminates the MIL.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0545 Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine.
P0546
P2032
P2033

WIRING DIAGRAM

A210276
5.99,3.281 6.354,3.479 0.365,0.198 10 false ECM 5.688,1.865 6.125,2.063 0.438,0.198 10 false THCO 5.688,2.698 6.125,2.896 0.438,0.198 10 false ETCO 1.438,2.281 4.708,2.635 3.271,0.354 10 false NO. 2 Exhaust Gas Temperature Sensor (B1S2) 5.688,0.542 6.125,0.74 0.438,0.198 10 false THCI 5.688,1.448 6.125,1.646 0.438,0.198 10 false ETCI 1.344,0.885 4.094,1.083 2.75,0.198 10 false Exhaust Gas Temperature Sensor (B1S1) 5.302,0.438 5.563,0.604 0.26,0.167 10 false 122 5.375,1.271 5.563,1.458 0.188,0.188 10 false 99 5.313,1.771 5.604,1.938 0.292,0.167 10 false 121 5.292,2.604 5.563,2.781 0.271,0.177 10 false 120 6,3.135 6.281,3.292 0.281,0.156 10 false B76 1.333,0.698 1.615,0.885 0.281,0.188 10 false B59 1.438,2.083 1.719,2.26 0.281,0.177 10 false B60 1.99,0.427 2.125,0.594 0.135,0.167 10 false 1 2.802,0.427 2.948,0.635 0.146,0.208 10 false 2 1.99,1.781 2.125,1.948 0.135,0.167 10 false 1 2.802,1.781 2.948,1.99 0.146,0.208 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).


HINT:

If DTC P2033 is stored and the exhaust gas temperature sensor (B1S2) circuit is not malfunctioning, check if the DPF catalytic converter has melted as DTC P2033 may be stored when the DPF catalytic converter melts and the exhaust gas temperature sensor (B1S2) is exposed to high temperatures.


PROCEDURE

1.READ VALUE USING GTS (EXHAUST TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1 and Exhaust Temperature B1S2.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S1
Exhaust Temperature B1S2
50003 61 1061,1062

d.

Read the value.

Standard:

Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after an engine speed of 3000 rpm is maintained for 1 minute.


Result:
Temperature Displayed Proceed to
0°C (32°F) (After warming up the engine) A
1000°C (1832°F) or higher B
OK: Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after maintaining an engine speed of 3000 rpm for 1 minute after accelerating the engine from idling to 3000 rpm C


HINT:
·

If there is a short circuit, the GTS will indicate 0°C (32°F).

·

If there is an open circuit, the GTS will indicate 1000°C (1832°F) or higher.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A204589
2.167,2.458 2.563,2.698 0.396,0.24 0.813,2.469 1.208,2.708 0.396,0.24 2.365,1.021 2.708,1.167 0.344,0.146 10 THCI 2.365,1.177 2.802,1.323 0.438,0.146 10 THCO 2.396,1.49 2.75,1.656 0.354,0.167 10 ETCI 2.396,1.646 2.813,1.792 0.417,0.146 10 ETCO 0.854,2.51 1.135,2.656 0.281,0.146 10 B59 2.219,2.49 2.49,2.646 0.271,0.156 10 B60 0.75,0.333 1.063,0.49 0.313,0.156 10 *1 2.656,0.26 2.969,0.417 0.313,0.156 10 *2 0.396,2.49 0.708,2.646 0.313,0.156 10 *a 1.813,2.49 2.125,2.646 0.313,0.156 10 *b
*1 Exhaust Gas Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Exhaust Gas Temperature Sensor (B1S1))
*b Front view of wire harness connector
(to No. 2 Exhaust Gas Temperature Sensor (B1S2))


Disconnect the B59 or B60 exhaust gas temperature sensor connector.


b.

Connect terminals 1 and 2 of the exhaust gas temperature sensor wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the intelligent GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1 and Exhaust Temperature B1S2.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S1
Exhaust Temperature B1S2
50003 61 1061,1062

f.

Read the value.

Standard:

1000°C (1832°F) or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE EXHAUST GAS TEMPERATURE SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
3.REPLACE EXHAUST GAS TEMPERATURE SENSOR

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Disconnect the exhaust gas temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B59-2 - B76-122 (THCI) Always Below 1 Ω
B59-1 - B76-99 (ETCI) Always Below 1 Ω
B60-2 - B76-121 (THCO) Always Below 1 Ω
B60-1 - B76-120 (ETCO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A208467
0.442,0.108 0.64,0.278 0.198,0.17 10 *1 2.459,0.108 2.657,0.278 0.198,0.17 10 *2 2.402,0.944 2.786,1.115 0.384,0.17 10 THCI 2.402,1.099 2.855,1.269 0.454,0.17 10 THCO 2.402,1.46 2.855,1.63 0.454,0.17 10 ETCI 2.402,1.626 2.855,1.796 0.454,0.17 10 ETCO
*1 Exhaust Gas Temperature Sensor
*2 ECM


Disconnect the B59 or B60 exhaust gas temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1 and Exhaust Temperature B1S2.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S1
Exhaust Temperature B1S2
50003 61 1061,1062

e.

Read the value.

Standard:

0°C (32°F)



f.

Reconnect the exhaust gas temperature sensor connector.


Result:
Proceed to
OK
NG



OK

7.REPLACE EXHAUST GAS TEMPERATURE SENSOR

NG

8.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
7.REPLACE EXHAUST GAS TEMPERATURE SENSOR

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Disconnect the exhaust gas temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B59-2 or B76-122 (THCI) - Body ground Always 10 kΩ or higher
B60-2 or B76-121 (THCO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.REPLACE ECM

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Start the engine.


f.

Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END