Refer to DTC P0112 (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P0112).
Refer to DTC P007C (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P007C).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P011C | Charge Air Temperature/Intake Air Temperature Correlation (Bank 1) | After the engine is completely warmed up and then allowed to soak for a long time (10 hours or more), the difference in temperature at the intake air temperature sensor and intake air temperature sensor (turbo) after turbocharger after idling for 3 minutes is 15°C (27°F) or higher.
(2 trip detection logic) |
·
Open or short in intake air temperature sensor circuit ·
Open or short in intake air temperature sensor (turbo) circuit ·
Intake air temperature sensor (built into mass air flow meter assembly) ·
Intake air temperature sensor (turbo) ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P011C | ·
Intake Air ·
Intake Air Temp (Turbo) |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P011C | After engine completely warmed up, allow engine to soak for long time (10 hours or more).
Start the engine and idle the engine for 3 minutes or more. |
Refer to DTC P0112 (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P0112).
Refer to DTC P007C (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P007C).
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Proceed to |
|---|
| DTC P011C is output |
| DTC P011C and other DTCs are output |
If any DTCs other than P011C are output, troubleshoot those DTCs first.
DTC P011C is output
DTC P011C and other DTCs are output
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DIAGNOSTIC TROUBLE CODE CHART
Allow the engine to soak for 1 to 2 hours.
It is not necessary to allow the engine to soak if the engine is cold.
The engine cools faster if the hood is opened.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant temp.
| Tester Display |
|---|
| Coolant Temp |
Read the value.
The difference between the displayed value and outside air temperature is below 5°C (9°F).
If the difference between "Coolant Temp" and the outside air temperature is 5°C (9°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
| Tester Display |
|---|
| Intake Air |
Read the value.
The difference between the displayed value and outside air temperature is below 15°C (27°F).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).
| Tester Display |
|---|
| Intake Air Temp (Turbo) |
Read the value.
The difference between the displayed value and outside air temperature is below 15°C (27°F).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the intake air temperature sensor (turbo) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A54-2 - B76-113 (THIA) | Always | Below 1 Ω |
| A54-1 - B76-90 (ETHI) | Always | Below 1 Ω |
| A54-2 or B76-113 (THIA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the intake air temperature sensor (turbo).
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the mass air flow meter assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B1-4 (THA) - B76-110 (THA) | Always | Below 1 Ω |
| B1-5 (E2) - B76-87 (ETHA) | Always | Below 1 Ω |
| B1-4 (THA) or B76-110 (THA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the mass air flow meter assembly.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Allow the engine to soak for 1 to 2 hours.
It is not necessary to allow the engine to soak if the engine is cold.
The engine cools faster if the hood is opened.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant temp.
| Tester Display |
|---|
| Coolant Temp |
Read the value.
If the difference between "Coolant Temp" and the outside air temperature is 5°C (9°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air and Intake Air Temp (Turbo).
| Tester Display |
|---|
| Intake Air Temp (Turbo) |
Read the value.
The difference between the displayed value and outside air temperature is below 15°C (27°F).
| Proceed to |
|---|
| NEXT |
NEXT